EVENTIDE MIXING LINK HIGH QUALITY MIX PRE

High Quality Mic Pre with FX Loop in a compact form factor

-FX Loop Send and Return supports Balanced and Unbalanced signals - interfaces with consoles or guitar pedals easily

-Latching or Momentary Footswitch control of FX Loop for performance effects

-Works with a wide range of microphones including condenser and ribbon mics with up to 65dB of clean gain

-Aux I/O connection supporting stereo input and send

-Guitar Amp output and Headphone monitor output with separate master volume control

-International universal power supply included

-Operates on 9V battery
 (No phantom power)

-48V Phantom power for Condenser mics

-Balanced XLR Output which supports DI and Line levels

-Instrument and Balanced Line level inputs

-Versatile Mix Control supports 3 modes- 100% Mic w/FX blended in, or Mic/FX balance control, or 100% FX (no Mic)

Analog Input     MAX Input Levels, Input Impedance
INST IN
    +10dBu, 500kΩ
XLR
LINE IN
    +24dBu, 22kΩ
XLR MIC IN
    +4dBu, 2kΩ
FROM FX
    +10dB, 200kΩ
AUX IN
    +4dBu, 5.0kΩ

 

Analog Output     MAX Output Levels, Output Impedance
TO FX
    +10dBu, 400Ω
TO AMP
    +10dBu, 250Ω
PHONES
    150mW per channel, min Load = 8 Ohms
DI/LINE OUT
    (DI) -10dBu, (LINE) +18dBu, 200Ω
AUX OUT
    18mV, 200Ω (mobile mic level)

 

 

Power Supply
9 VDC, 500 ma, center pin (-)
Minimum required current at 9VDC = 200mA

 

Dimensions

English:
3.6” (H) x 2.65” (W) x 1.5” (D)

Metric:
91(H) x 67(W) x 38(D) mm

 

Weight
0.96lb ,0.43kG

  

The PRE-73 Mk2 pre-amp and the FC3 condenser microphone in one bundle. The bundle also includes Golden Age P1 Pop Filter, Proel RSM180 mic stand and Proel CHL250 5m cable.

• • Ultra-high quality 8-channel A/D and D/A interface for virtually any digital recording/mixing environment
  • 8 state-of-the-art MIDAS designed Mic Preamplifiers
  • Phantom power on all microphone inputs
  • Reference-class Cirrus Logic 24-bit converters for ultimate signal integrity
  • Processes 48 and 44.1 kHz sample rates
  • External sample rate synchronization via word clock or ADAT input

• Optical ADAT in/out interface for ultimate compatibility
• All mic/line inputs routed to the ADAT output
• ADAT input routed to all Line outputs
• “Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
• High-quality components and exceptionally rugged construction ensure long life
• Conceived and designed by BEHRINGER Germany

 The OctaMic II provides 8-Channel 192 kHz / 24 bit AD conversion with eight hi-class microphone and line pre-amplification channels, featuring a combination of sophisticated components and approved RME technology.

Lowest distortion, excellent signal to noise ratio and perfectly linear frequency response transmit and amplify the microphone signals truly unchanged.

The OctaMic II includes some significant enhancements compared to the OctaMic:

The balanced TRS inputs of the Neutrik Combo XLR jacks are phantom power-free and can be operated as real line inputs too. The improved design of the input circuits allows for a maximum input level of +21 dBu with a convenient gain range from 6 dB up to 60 dB.
Improved signal to noise ratio (SNR) ADC 107.5 dB
Improved THD, especially at higher gains
Optimised heat dissipation by a new and larger housing with improved convection
Internal wide range power supply with line filter, insensitive to voltage fluctuations
Super-stable, short circuit proof 48 V phantom power


Features

OctaMic II offers 8 balanced XLR mic / line inputs via Neutrik XLR/TRS combo jacks. Each channel contains switches for 48V phantom power, a low cut filter and phase reversal. Amplification can be set between 6 and 60 dB. LEDs for signal, clip, and activated phantom power give a complete overview on the unit's status. When the special Clip Hold mode is activated, any detected clip-state will cause the corresponding LED to flash once per second. With this, the user gets a long-term peak detection, and no longer needs to constantly watch the LEDs. At the same time momentary overloads are still displayed correctly.

Frontside switches include power on/off and output level, for a choice of -10 dBV, +4 dBu or Hi Gain (+19 dBu) as reference level. This unusual feature offers two advantages. First, the reference level can be easily switched to match any of RME's current interface devices, from HDSP 9632 through Multiface up to the renowned ADI-8 series converters. Second, the Signal to Noise ratio is optimized, and the Clip-LED will exactly match the ones of the ADI-8 (2 dB below 0 dBFS).

The balanced line level output signal is available at the back of the unit via 8 stereo TRS jacks. The specially developed, internal hi-performance switch mode power supply lets the OctaMic II operate in the range of 100V to 240V AC. It is short-circuit-proof, has an integrated line-filter, is fully regulated against voltage fluctuations, and suppresses mains interference.

Top
AD-Conversion

The 8-Channel AD-conversion of the OctaMic II operates at up to 192 kHz. The digitized signal is available simultaneously at the double ADAT output (S/MUX, up to 96 kHz), and at a DB-25 connector (4 AES/EBU outputs, up to 192 kHz). The digital part can be clocked internally (master) and externally via word clock, AES/EBU and SPDIF.

RME's outstanding SteadyClock(TM) ensures perfect AD-conversion, as jitter on the external sync-sources is nearly completely removed. All settings are done via DIP-switches on the back of the OctaMic II. Analog outputs and both digital outputs operate fully simultaneously. The choice of reference level affects the analog outputs only, the signal/clip indication and the AD-conversion will react only to the Gain-pots.


Top
Tech Specs

8 balanced XLR/TRS mic/line inputs

54 dB gain range

Input impedance: XLR 2 kOhm, TRS 5 kOhm

Analog input level: from -40 dBu up to +21 dBu

Maximum output level: +21 dBu

Output impedance: 75 Ohm

Output level switchable Hi Gain / +4 dBu / -10 dBV

Signal to noise ratio (SNR): 129 dB EIN @ 150 Ohm

THD:
Large frequency range (200 kHz) with special EMI input filtering

Frequency response -0.5 dB: 5 Hz - 200 kHz

Hi-pass filter: 80 Hz, 18 dB/oct.

Line Out: 1/4" TRS (6.3 mm stereo jack), servo-balanced

Phantom power: +48 Volt switchable per channel

Internal wide range switching power supply 100-240 Volt AC

Unbeatable price/performance ratio!

AD conversion

SNR: >110 dB(A)

Supported sample rates: 28 kHz - 200 kHz

THD:
Sync Sources: AES/EBU (also SPDIF coaxial), wordclock, internal

SteadyClock(TM) ensures best sound quality even with jittery external clocks


Top
Accessories

Digital breakout cable Pro, AES/EBU, D-sub25 to 4x XLR-3 female + 4x XLR-3 male, 1m/3m/6m (ALVA Audio)
Digital D-sub cable, AES/EBU, D-sub25 male to D-Sub25 male, 1m/3m/6m (ALVA Audio)
Optical ADAT Toslink cable 1m/2m/3m/5m/10m (ALVA Audio)
Word Clock cable, 1 x BNC male to 1 x BNC male, 1m/5m/10m (ALVA Audio)

Top
Add-On

BOB-32    Universal Breakout Box with 2 x 8 XLR to 2 D-sub connectors (supports TASCAM and YAMAHA format), flip-frame case

The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.

The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

Features  :

• Vintage Style electronics. No intergrated circuits in the signal path.

• Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

• GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).

• Tantalum capacitors in the signal path.

• Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.

• Switchable phantom power and absolute phase.

• A high-impedance instrument input for any sound module, electric guitar or bass.

• A simple but effective 4-step LED output level meter.

• The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.

• Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.

• Insert jack for inserting EQ´s and other units.

• Selectable 600 ohm output termination.

• The pcb is prepared for the Carnhill input transformer.

• External power supply to avoid interaction with the audio circuits and transformers.

• A solid build quality that will last many years of normal use.

The MKIII has the following new features compared to the MKII:

• Tantalum capacitors in the signal path.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.

• The pcb is prepared for the Carnhill input transformer.

• Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.

• All GAIN settings can also be used in LINE mode .