| Content | The DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of XLR, TRS, and RCA sockets, plus a switchable 20 dB pad and a ground lift switch.
In addition, the DN200 can operate in Sum mode, where left and right input signals are merged and routed to both left and right outputs, or Split mode, routing the left input signal to both the left and right outputs. The DN200 supports 24 to 48V phantom-power operation.
Dual-channel active direct injection boxRugged Neutrik Combo XLR connectors featuring high-impedance DI jack inputsRCA Phono inputsIndependent phantom power for each channel for maximum reliabilitySum switch optionally routes both inputs to both outputsSplit switch optionally routes left input to both outputsGlobal 20 dB Input Pad and Earth Lift switches24 to 48V phantom-powerStackable, protective silicone rubber sleeveCompact and rugged design | Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm. |
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
< 0,7 % bei 40 Hz
powering 9-V battery (IEC 6LF22) or
phantom power 24 ... 48 V.
inputs two 1/4" phone jacks , unbalanced
(one being used as output to instruments amp)
outputs XLR, balanced
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm |
Passive DI box especially designed for guitars.
The PDI09 can be connected between an effect device or amplifier and the mixing console. The PDI09 is not suitable for direct connection to a guitar. Integrated filter circuits simulate the authentic "speaker" sound. Tone can be varied between "Mellow“, "Normal“, or "Bright“.
Technical specifications:
- Input: 6.3 mm jack with parallel "THRU" socket
- Output: male XLR transformer balanced
- Attenuator: (Level switch) 0 dB for line signals, -15 dB for small amps up to 10 w, 30 dB for large amps up to 200 w
- No battery necessary
|
Inline Transformer IA-2
The model IA-2 line matching transformers !S designed to properly match a low impedance
signal to a low impedance source. The advantage of "ground lift" switching allows to optmize
hum problems.
Technical Data
Frequency response 20 Hz - 20 KHz + 1 dB
Impedance 600 : 600 Ohm
THD K3 50 Hz = 0.5 %
Level < + 6 dBm
Weight 100 g
Dimensions diameter 17 mm, lenght 115 mm
|
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
|
Reviews
There are no reviews yet.