| Content | The DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of XLR, TRS, and RCA sockets, plus a switchable 20 dB pad and a ground lift switch.
In addition, the DN200 can operate in Sum mode, where left and right input signals are merged and routed to both left and right outputs, or Split mode, routing the left input signal to both the left and right outputs. The DN200 supports 24 to 48V phantom-power operation.
Dual-channel active direct injection boxRugged Neutrik Combo XLR connectors featuring high-impedance DI jack inputsRCA Phono inputsIndependent phantom power for each channel for maximum reliabilitySum switch optionally routes both inputs to both outputsSplit switch optionally routes left input to both outputsGlobal 20 dB Input Pad and Earth Lift switches24 to 48V phantom-powerStackable, protective silicone rubber sleeveCompact and rugged design |
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
|
Passive DI box especially designed for guitars.
The PDI09 can be connected between an effect device or amplifier and the mixing console. The PDI09 is not suitable for direct connection to a guitar. Integrated filter circuits simulate the authentic "speaker" sound. Tone can be varied between "Mellow“, "Normal“, or "Bright“.
Technical specifications:
- Input: 6.3 mm jack with parallel "THRU" socket
- Output: male XLR transformer balanced
- Attenuator: (Level switch) 0 dB for line signals, -15 dB for small amps up to 10 w, 30 dB for large amps up to 200 w
- No battery necessary
| Product Features:
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Switchable input attenuation allows input levels of up to +50 dB
Ground Lift switch eliminates typical ground loop problems
¼" TRS and gold-plated XLR connectors
Ultra-rugged, road-suitable aluminum case
Stackable oversized rubber corners
High-quality components and exceptionally rugged construction ensure long life and durability
Conceived and designed by BEHRINGER Germany
With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners. | |
Palmer PAN 03
19" DI Box 4-Channel active
Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.
Product type
DI Boxes
Type
active
Channels
4
Inputs
4
Input connectors
6.3 mm jack
Max. input level
+ 45 dBu
Input impedance
(@ 60 Hz) 1 M Ohm(s)
Input pad
0 / -30 dB
Outputs
4 (+ 4 parallel XLR outs)
THRU outputs/channel
1
Output connectors
6.3 mm jack , XLR
Max. output level
+ 10 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 20000 Hz
Transformer balanced
Yes
Ratio
10 : 1
Indicators
Power
Controls
attenuator , ground lift
Operating voltage
external
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
480 mm
Width
19 "
Depth
90 mm
Height
45 mm
Height
1 U
Weight
1,6 kg
|
Reviews
There are no reviews yet.