Content |
At PreSonus, weʼve been designing preamps for a long time, and we always focus on audio quality first. So when we decided to upgrade our popular TubePre V2, we focused on improving an already high-quality sound—without jacking up the price. Like the originalTubePre, the new version is a fully professional tube preamp, with a dual-servo (no capacitors) gain stage that lets you boost the program signal to smoking hot levels without significantly increasing the background noise. Discrete components and high-voltage operation offer dynamic range and detail not found in other single-channel tube preamps in its class.
Housed in a rugged case, the TubePre V2 rear panel sports separate unbalanced, ¼” instrument and balanced, XLR mic inputs and unbalanced ¼” and balanced XLR line outputs. Weʼve included all of the extras you need for professional operation including a high-pass filter, phantom power for condenser mics, polarity reverse switch, and a backlit VU meter.
|
The AD2022 is Avalon's fourth generation of fully discrete, symmetrical Pure Class A microphone preamplifiers. The dual mono AD2022 includes the original sonic capabilities and transparency of the M2, M22 and M5 preamplifiers plus several additional features, including selectable microphone source loading for optimized cable/mic matching, improved high-voltage Class A regulated power supplies, two high Z instrument inputs, variable-passive high pass filter, teflon/ silver wiring and doubled plated circuit boards for superior low level signal transfer. AD2022 FEATURES Symmetrical Pure Class A design, two channels Microphone and hi-Z instrument inputs Gain switched 4dB steps plus +/- 3dB fine output trim Selectable microphone input impedance matching Low noise -126dB EIN Ultra high quality, low-ratio, balanced input transformer Balanced, high-current Class A output to +36dB Large illuminated analog VU meters and twin peak LED's Regulated phantom power supply +48v Input polarity phase reverse High headroom +36dB input before overload Input -20dB pad for high level signals Sealed silver relays for all signal routing External AC 150w toroidal power chassis Fully discrete Class A regulated audio power supplies Deep, musical sound-stage, transparent amplification
MICROPHONE INPUT The AD2022 incorporates the most advanced high-performance microphone transformer available. Split low-ratio primary windings are carefully combined within a custom mu-metal core for extended smooth frequency response and very low distortion. Sealer silver relays are used for minimal signal invasion. The input signal selector, high pass filter, polarity-phase reverse, +48v power and the 20dB input attenuator all utilize local sealed relay operation. A variable passive high pass filter provides a minimum phase shift design while eliminating low frequency rumble, wind noise and mechanical vibration at sub sonic frequencies.
SYMMETRICAL PURE CLASS A DESIGN Two 100% discrete, high-voltage, symmetrical Pure Class A signal amplifiers are utilized per channel. The first operates in a cascaded-cascode FET configuration while the second stage amplifier is fully bipolar. The twin amplifiers share the total available gain requirement. This shared architecture increases the high level headroom capability, improves transient response and doubles the internal bandwidth of the ultra-high performance pure Class A signal amplifiers. OUTPUT and METERING High-current DC coupled, Class A discrete amplifiers are utilized for the output drive interface with +36dB capability into all known loads. Two large, high-quality analog VU meters indicate accurate signal readings while bi-color LED's offers peak indication at 0dB and +20dB.
AD2022 PREAMPLIFIER SPECIFICATIONS Circuit Topology: Twin cascode FET and bipolar low level signal amplifiers, high-voltage, 100% discrete, symmetrical Pure Class A Input Type and Load: Transformer balanced low-ratio, 50, 150, 600 and 1k5 ohm input load selection Maximum Mic Level: +36dB balanced XLR pin 2 hot (with -20dB passive attenuator) Maximum Instrument Level +18dB at 100k ohms instrument input level, standard mono 1/4 inch jack Input Attenuator: -20dB resistive pre transformer primary, sealed silver relay Phantom Power: +48v regulated 50mA capability, sealed silver relay High Pass Filter: Passive, variable from 30Hz to 185Hz @ 6dB per octave, sealed silver relay. Polarity Reverse: Sealed silver relay on microphone input Gain Range Input: +20dB to +64dB in 4dB steps Gain Output Range: +/- 3dB variable conductive plastic potentiometer Maximum Output Level: +36dB balanced 600 ohms, DC coupled, discrete symmetrical Pure Class A Output Type: XLR connector, pin 2 hot Noise EIN Unweighted: -126dB 150 ohm Noise 20kHz Unweighted: -102dB Distortion THD, IMD: 0.05% nominal Frequency Response -3dB: 1Hz to 120kHz transformer limit System Bandwidth: DC to 1MHz Output Meter: High quality, illuminated analog VU meter 0dB = +4dB. Peak Meter: Bi-color LED's 0dB and +20dB peak detection circuit. AC power supply B2T: External toroidal 100V to 240V, 50-60Hz selectable, 150 watts maximum. Cables: 90V ac, 4 pin male power input connector, B2T required, internal DC regulation Dimensions: 19 x 12 x 3.5 in (482 x 305 x 89mm) Weight: 15lbs (6.8kg) Dimensions - Shipping Carton: 24 x 21.5 x 7.5 in (610 x 546 x 190mm) Weight - Packed: 25lbs (11.4kg) |
The CPR12 is an easy to use, flexible and multifunctional 10 channel pre-amplifier. Six of these input channels are selectable between Mic / Line level and equipped with a 3 band tone control. The first two can be switched to priority and phantom power. The other four channels are direct line inputs. Every input channel has its own gain and fader volume control with PFL button which makes it possible to pre-listen each input or output channel with the built-in pre-listening speaker, and can be routed to one or both output channels. This makes the CPR12 a full two-zone system. Other present features are a priority input, a recording output, separate sub-out channels and the 24 V DC emergency power connection. This last feature makes it possible to power the CPR12 with emergency power when the main power is shut down. In this case, the priority input will automatically mute all input signals, and a evacuation message will be announced. The steel 19" housing has a height of 2 HE. - 10 audio input sources
- 6 Mic / Line inputs with 3 band EQ
- 4 Direct Line Inputs
- Fader volume control
- Two output zones
- Built-in pre-listening speaker
- Priority input for emergency situations
- + 15 V DC Phantom power
- Works on 24 V DC emergency power
Specifications - Model Name / Type: CPR12 / 10 channel 2 zone pre-amplifier
- THD+N:
- Signal/Noise: > 90 dB
- Frequency Response: 20 Hz - 20 kHz
- Phantom Power: + 15 V DC
- Emergency Power: + 24 V DC
- Power Supply: 100 - 240 V AC / 50 - 60 Hz
- Dimensions (W x H x D): 420 x 88 x 320 mm
| • Solid housing
• RIAA Equalization
• High quality components
The PRE-101 is a phono pre-amp with RIAA equalization. The tiny signal of magnetic pick-ups is amplified to fit the line-level inputs of mixers or USB sound-cards.
Specifications Frequency Response: 20Hz-20KHz RIAA
Inputs: RCA
Outputs: RCA
Input sensitivity: 3mV for 1000 mV output
Input Impedance: 47 kOhm
Nominal Output Voltage: 0 dBV
Max Output voltage: +16 dBu
Output impedance: 100-600 Ohms
Power supply: 18V AC (adapter included)
Dimensions: 40 x 113 x 80 mm (HxWxD)
Weight: 0,35 Kg |
Behringer MIC-2200 2-Channel Tube Microphone Preamplifier-Line Driver-DI Box The MIC2200 is the ideal extension to your console, MIDI setup or hard disk recording system. Its integrated parametric EQ?s give you extra sound-shaping power, while its built-in tube adds warmth and transparency to your signal. In addition, the ULTRAGAIN PRO features direct injection and level conversion functionality.
|
EWI PDI-100 PARA ACOUSTIC DI Box
This is a medium grade professional application Para Acoustic Active DI, which will work well on instruments with passive pickups or active pickups.
The construction is reasonably rugged and the components are well suited for the application yielding results that are typically acceptable for all but the most discerning artists.
The on-board tone and volume controls give the operator a lot of choices in shaping their sound prior to sending the signal to the mix console. This allows an artist to use this device in-place of or in addition to a traditional stage amp for their instrument. This is an excellent choice for IEM bands, or bands that like to keep their stage volume low.
This item is typically used to split the instrument signal going to a stage amp so a feed can be sent also to the mix board, or be used as a stand-alone instrument pre-amp. It is equipped with a ¼” jack for input, a 1/4" jack for output to a stage amp, one XLR jack for the send to the board and a TRS jack for inserting an FX device.Since this is an active D.I. box, it needs to be powered which can be done either with Phantom Power from the mix board, or with the supplied internal 9v battery. The battery is fairly easy to change by removing one screw in the bottom of the case.
|
Reviews
There are no reviews yet.