Content | KODA REACT PA-70 Amplifier with bluetooth, usb, tuner radio, 150W 100V
Priority input and radio 150W
USB or Card reader
2 AUX in, 1 AUX out
2 mic in (1 with priority)
With remote control
Output 8-16Ω/70V/100V, 1 zone |
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 400: 2x 200 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 17 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
Specification |
| Power Source | 220 - 240V AC or 24V DC | Rated Output | 30W | Power Consumption | 34W (EN60065), 78W(AC operation at rated output, 2A (DC operation at rated output) | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | Distortion | Under 1% at 1kHz,1/3 rated power | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:330W (100V)
LOW IMPEDANCE: 4Ω (11V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | Phnatom Powe | DC + 21V (MIC 1) | S/N Ratio | Over 60dB | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | Indicator | Power signal, peak | Finish | Panel: ABS resin, black/Case: Steel plate, black | Dimensions | 420 (W) x 100.9 (H) x 280.2 (D) mm | Weight | 5kg |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
Specification |
| Power Source | 220 - 240V AC or 24V DC | Rated Output | 240W | Power Consumption | 238W (EN60065), 520W(AC operation at rated output, 15A (DC operation at rated output) | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | Distortion | Under 1% at 1kHz,1/3 rated power | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:42W (100V)
LOW IMPEDANCE: 4Ω (31V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | Phnatom Powe | DC + 21V (MIC 1) | S/N Ratio | Over 60dB | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | Indicator | Power signal, peak | Finish | Panel: ABS resin, black/Case: Steel plate, black | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | Weight | 13kg |
|
- HIGH POWER, LOW DISTORTION
120W of RMS power with less than 1% THD.
- ADVANCED PROTECTION CIRCUITRY
Thermal and current overload protection, power-on delay and automatic idling circuitry for component and loudspeaker protection.
- BATTERY BACKUP
Can be powered by 24VDC battery for emergency backup and true portability.
- SLIM DESIGN, COMPACT SIZE
Streamlined design fits in a compact 3RU space.
PA- 2312
|
Rated Output (RMS, THD 1%, 1kHz)
|
120W
|
Input Sensitivity/Impedance
|
1V/10kΩ, Balanced
|
T.H.D
|
Less than 1%
|
S/N
|
Better than 95dB
|
High Pass Filter
|
-3dB at 400Hz
|
Channel Separation
|
Less than –70dB
|
Output Voltage/Impedance
|
EC, JAPAN: 4Ω/22V, 41Ω/70V, 83Ω/100V
|
USA/CANADA: 4Ω/22V, 5.2Ω/25V, 41Ω/70V
|
Power Source
|
100–120VAC or 220–240VAC; 50/60Hz, 24VDC
|
Power Consumption(1/8 Power)
|
290W
|
Weight
|
20Kg/44.1Ib
|
Dimensions
|
482(W) x 132(H) x 280(D)mm/19(W) x 5.2(H) x 11(H)in
|
|
Reviews
There are no reviews yet.