| Content |
Want to make sure that your trussing is aligned?
Want to know the height of the venue?
Want to know the volume of the room?
No problem! Know it in a few moments with this Ultrasonic Distance Meter!
• Calculates area and volume
• Laser to target the point from where
you want to measure
• Auto converts feet to meters
• Backlight
Specifications
Measurement range: 0,6 to 15 m
Accuracy: ± 0,5% ± 1 Digit
Resolutions: 0,01 m
Aperture angle: ±5°
Power supply: 6F22(9V) x 1
Dimensions: 136 x 59 x 38 mm
Weight: approx. 150 g (incl. battery)
| Tests XLR, 1/4 in., 1/8 in., TT, RCA and MIDI connectors.
The intelligent, CPU-controlled CT100 accepts virtually any connector type:
XLR, mono and TRS phone (1/4 in., 1/8 in., TT), RCA and MIDI. It shows
which input pin is connected to which output pin. Separate LEDs indicate
proper shield connection and phantom power presence. The CT100 also
offers an installed cable test mode and a continuity check plus a test tone
generator.
Features
3 modes: cable test mode, installed cable test mode, and test tone mode
Accepts XLR, mono and stereo TRS phone (1/4 in., 1/8 in., TT),
RCA and MIDI Connectors
Continuity check
Intermittent detect
Phantom power detect
Grounded shield detect
Test tone generation (1 kHz and 440 Hz)
Battery operation (requires 2 AA alkaline batteries) |
This is an on-the-road tool you certainly can't miss in your gearbox! A nifty, handy cabletester, which allows you to check up to six (welding) connections and gives you a visual readout by 2 rows of 6 LED's. The checking itself is done manually per connected pin. A LED will light up to indicate what pin is connected correctly on which side. A short-circuit check with a red LED and audio-warningsignal is also included. On the left and right side you'll find inputs for 6,3 symm. jack, BNC, RCA, 5p. DIN, 5p. XLR, 3p. XLR and Neutrik® Speakon®.
|
Minirator MR1 is the powerful analog audio generator providing a comprehensive
set of analog audio test signals required in a professional audio environment.
This handy audio generator enables you to stimulate any analog device with a
broad range of appropriate signals like sine wave, pink noise, white noise,
sweeps and many others, for performance checking, maintenance and repairs.
Convenient, reliable and optimized - Minirator fits into your pocket as well as in
your budget.
Product-details
Signals:
? Sine Wave
? Square Wave
? Frequency Sweep
? White Noise
? Pink Noise
? Polarity Test Signal
Features:
? 20Hz to 20kHz, adjustable
in 1/3rd octave steps
? Level adjustable
? Low distortion
|
The PMBL is a 2 channel passive line level merge box. Each channel has 2 balanced XLR/f inputs. The input signal is merged via a resistor network to a XLR/m output.The top side input is transformer isolated. Possible applications might be the routing of two mixing desks to one power amp or mixing a stereo signal down to mono. Our transformer technology allows for an unbalanced top side input to be sent out balanced.
Specifications:
- Each Channel: Input 1 transformer balanced XLR/f. Symmetrically decoupled through resistors
- Total ohmic value: 2 K Maximum level for THD
|
The MiniSPL is the perfect accessory to the Acoustilyzer & Minilyzer for
acoustical measurements.
The MiniSPL is a battery powered measurement microphone. Together
with the Acoustilyzer or Minilyzer, it forms an acoustical analyzer and integrating
sound level meter. Additionally it may be operated as a stand-alone microphone
e.g. connected to a balanced audio-line, a microphone-input or a sound-card.
Product-details
? Battery powered
? Factory-set sensitivity
? No phantom power required
? 1/2" microphone, class 2 acc. IEC 61672
? Omni-directional
? Supplied with mic clamp, wind protection
? Typical frequency response included
MiniSPL together with Acoustilyzer:
? SPL Meter / RTA
? Reverberation Time RT60
? Delay Time
? FFT Analyzer
? Speech Intelligibility STI-PA
MiniSPL together with Minilyzer:
? Measurements: SPL, min./max., Leq
? 1/3rd octave spectrum analyzer |
Reviews
There are no reviews yet.