| Content | Portable Battery phantom power supply for microphones with TQG and AKG connection.
Balanced XLR output
2 three-pole TQG male inputs (Mini XLR)
Both inputs adjustable
On-off switch
Mic / Line level in the output switchable
9 V battery power
20 hours of operation with 1 battery
Power LED | PS418D
Pre-Amplifier
The condenser miniature microphones, need phantom power to work. The PS418D is just what they need. It can be powered by phantom power or battery, and switchable low cut filter helps to reduce low band noise.
Features:
• Two options for Power Requirements: phantom or battery.
• Low-cut filter switch.
• Transistor output transformer circuit.
Specification:
Frequency Response: 25-20,000 Hz
Output Impedance: phantom 200Ω; battery 270Ω
Min. Load Impedance : 1000Ω
Power Requirements: phantom 9-52VDC，2mA; battery 1.5V AA/UM3
Low Frequency Filter: 80Hz @ 12dB / oct
Connector: TA3M (input), XLR3M (output)
Dimension(WxHxD): 63X84X22.5mm (2.48"x3.3"x0.89")
Weight: 245 g
Packaging: white box |
Introducing the ES947LED, the new LED-equipped version of the Engineered Sound ES947 table-mount boundary microphone. The ES947LED features a touch-sensitive capacitive switch and LED status ring.
The cardioid condenser ES947/LED increases usability with a new toggle switch and LED status ring - which displays red when muted and green when switched on. The new LED-equipped version of the highly respected ES947 also features improved sensitivity and sound-to-noise ratio, perfectly suited to todayʼs digital matrix mixers.
The ES947/LED is available in black and white.
ES947LED Specifications 263 KB
|
Shure P4HW Wired Bodypack Personal Monitor
P4HW Wired Bodypack
Hardwired Bodypack
Key Features
Attached input cable
High-impact plastic chassis
Operating Controls:
Operating mode (Stereo, Mono, MixMode)
Volume knob
Balance knob
Defeatable limiter
High-frequency boost
-15 db Pad
Backlit LCD Indicators :
Battery life
Input level
Operating mode
Frequency Response
20 to 20,000 Hz
Total Harmonic Distortion
Channel Separation
35 dB (minimum)
Signal-to-noise ratio
85 dB (minimum)
Maximum Output Level
+5 dBu at 1% THD
Maximum Input Level
+7 dBu, input pad OFF
+22 dBu, input pad ON
Actual Input Impedance
> 40 kilohms
Audio Output Connector
3.5 mm stereo (left=tip, right=ring, ground=sleeve)
Power Requirements
9 V Alkaline battery
Battery Life
Up to 8 hours, volume dependant
Phantom Power Protection
Up to 60 VDC
| Gravity MA 3D A POP 1 Traveler 3D Arm with Pop Filter
The Traveler Series' Pop Filter with 3D Arm
Every bit of weight counts when you're travelling by plane or truck from one gig to the next. After all, you can't always rely on the concert venue having the right tool available for you when needed.
The Pop Filter with 3D Arm MA 3D A POP 1 can be taken everywhere you go. It's so light and space-saving, there's absolutely no need for you to worry about weight or storage space.
With this tool you can enhance your voice- and vocal recordings by placing the high-quality pop filter, with double nylon mesh and a large screen diameter of 15.7 cm between you and your microphone. This way you avoid unwanted pop noises and clipping.
Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm lets you mount it on all popular microphone stands, and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws. Voila - you're all done! Once set, the MA 3D A POP 1 stays locked in place.
Gravity® has once again delivered a small, useful and reliable product for you to round off your collection of stands.
| Product type |
Microphone Accessories |
| Type |
Pop filter |
| Material |
Plastic, Polyamide |
| Color |
Black |
| Joint adjustment |
Wing screw |
| Joint rotation |
360° |
| Joint tilt |
180° |
| Arm length |
400 mm |
| Suitable for mounting on |
Microphone Stands |
| Thread size |
3/8” |
| Screen diameter |
157 mm |
| Setup |
Double nylon screen, plastic frame |
| Suitable for tube diameter |
15 - 35 mm |
| Weight |
0,377 kg |
|
With the AKG MDAi CPA Connected PA microphone adapter, all your favorite dynamic vocal mics instantly become part of the HARMAN Connected PA system. Simply attach the device to any input of your Soundcraft Ui24r mixer and then plug-in your dynamic mic and mic cable for automatic recognition with the HARMAN Connected PA app and ecosystem?providing effortless set up, instant recall of performer and presets, and great sound for musicians of all skill levels.
Current products with embedded ioSYS technology and HARMAN Connected PA compatibility include the Soundcraft Ui24R mixer, JBL PRX800W loudspeakers, dbx Di1 direct boxes, and AKG P5i microphones. |
Reviews
There are no reviews yet.