Content | The DS201 is a sophisticated dual channel noise gate incorporating a number of features pioneered by Drawmer, which are invaluable to the sound engineer, and not found on conventional noise gates.
Features:
- Variable high pass and low pass filters for "frequency conscious" gating.
- Comprehensive envelope control, attack, hold, decay, and range.
- Key input for external triggering.
- “Key Listen" facility.
- Extremely fast attack time, to preserve the natural attack of the sound.
- Balanced inputs and outputs.
- Stereo linkable.
- Can be used for "Gating" or "Ducking“.
- High audio specification.
These features and its "user friendliness" have made it the "industry standard" throughout the world.
Setting up noise gates can be tedious and unrewarding. For example, when attempting to separate a signal from unwanted noise or crosstalk that is relatively high in level, spurious triggering of the gate by unwanted components within the sound can be a serious problem. This can often be experienced in the studio when recording a drum kit. If a gate is used to clean up the snare drum sound it is quite likely that the nearby hi-hats will spill into the snare drum microphone and cause the gate to open. Increasing the threshold level may cure this problem, but then there is a very real danger that any quieter snare drum beats may not cause the gate to open at all and the performance can easily be ruined.
The DRAWMER solution to this problem is the inclusion of two variable filters, one high-pass and one low-pass, which act upon the side-chain keying circuitry. By setting the output switch to key listen the user can hear the action of the filters and adjust them to reject high frequency spillage from the hi-hats. This now enables the gate to only open on the lower frequencies present in the snare drum.
Drawmer pioneered the concept of frequency conscious gating, and the Drawmer DS201 was the first noise gate to include this feature.
The very fast attack of the DS201 means that it can open in a matter of micro seconds, thus preserving the natural attack of whatever sound is being gated and the comprehensive envelope controls mean that the gain can be changed at whatever rate best suits the material being processed. With vocals for example, a fairly fast attack is needed so as not to clip the leading consonants but a slower release time will prevent the end of words being clipped off and will also fade out any noise gradually rather than cutting it off abruptly. This latter point is very important as the human ear is far more sensitive to rapidly changing noise levels than to a constant low level noise.
Another important role played by the gate is in the reshaping of existing sounds. An example of this might involve a simple sampling delay line used to store a sound to be re-triggered later and added to a mix. A gate can be used to impart a slower attack or faster decay to the sound and careful setting of the decay envelope can effectively hide any noise present at the end of the sample. When using a sampler or drum machine the gate can be considered a triggered envelope shaper, and the wide range allowed by the envelope controls make the DS201 ideal for this application.
The unit can be switched to accept a key input, which allows the gate to be triggered externally. An example of this would be to use a snare drum signal to open the gate on a separate ambient microphone to create a natural alternative to gated reverb.
Each channel can be individually switched from Gating to Ducking for 'voice over' applications or the removal of 'clicks' and 'pops'. |
The Multicom Pro-XL MDX4600 gives you 4 channels of first-class dynamic
control in a single rack space. With a multitude of new features like the
advanced program-adaptive expander gate, extensive metering plus a variety
of configuration options, the Multicom Pro-XL puts a lot of dynamic processing
power in your rack.
Features
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression
circuitry combines the advantages of hard-knee and soft-knee characteristics
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible noise
suppression
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable low contour filter prevents "pumping" due to low-frequency dominated
compression
Stereo couple function selectable for channels 1/2 and 3/4
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 8-segment LED meters for input/output levels and gain reduction
Selectable operating level (+4 dBu/-10 dBV)
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Manufactured under ISO9000 certified management system
|
DBX-1074
4 ch noise gate με δυνατότητα λειτουργίας σε ρυθμιζόμενο εύρος
συχνοτήτων XLR in/out, insert points.
- Four independent channels of gating
- Independent key filtering
- Independent Threshold and Release controls
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Stereo Coupling mode
- Switchable +4dBu or -10dBv operation per channel
Input Connectors | XLR (Pin 2 and tip hot) | Input Type | Electronically balanced/unbalanced, RF filtered | Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm | Max Input | > +22 dBu balanced or unbalanced | CMRR | 40dB: Typically >55 dB at 1 kHz | Key Input | Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm | Output Connectors | XLR (Pin 2 hot) | Output Type | Servo-balanced/unbalanced, RF filtered | Output Impedance | Balanced 60 Ohm, unbalanced 30 Ohm | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | Frequency Response | 0.35 Hz to 200 kHz, +0/-3 dB | Noise | | Dynamic Range | > 115 dB, unweighted | THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | Interchannel Crosstalk | | Stereo Coupling | True RMS Power Summing | Operating Voltage | 100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | Power Consumption | 30 Watts | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | Power Connector | IEC receptacle | Unit Weight | 6.9 lbs. | Shipping Weight | 9.3 lbs. |
|
DBX-1046
Compressor - limiter 4 εισόδων, κύκλωμα "overeasy“, peakstoplus,
είσοδοι - έξοδοι XLR και 1/4 TRS. Κατάλληλος για studio, live χρήση.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | Input Type | Electronically balanced/unbalanced, RF filtered | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | Max Input | > +22 dBu balanced or unbalanced | CMRR | Typically >50 dB at 1 kHz | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | Output Type | Servo-balanced/unbalanced, RF filtered | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | Noise | | Dynamic Range | > 118 dB, unweighted | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | IMD | | Interchannel Crosstalk | | Stereo Coupling | True RMS Power Summing | Compressor Threshold Range | -40 dBu to +20 dBu | Compressor Ratio | 1:1 to infinity:1 | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | Compressor Attack/Release Characteristic | AutoDynamic™ | Compressor Attack Time | Program-dependent | Compressor Release Time | Program-dependent | Compressor Output Gain | -20 to +20 dB | Limiter Threshold Range | 0 dBu to +24 dBu (off) | Limiter Ratio | infinity:1 | Limiter Type | PeakStopPlus® two-stage limiter | Limiter Stage 1 | PeakStop® brickwall limiter | Limiter Stage 1 Attack Time | Zero | Limiter Stage 1 Release Time | Zero | Limiter Stage 2 | Predictive intelligent program limiter | Limiter Stage 2 Attack Time | Program-dependent | Limiter Stage 2 Release Time | Program-dependent | OverEasy® Switch | Activates the OverEasy compression function | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | Bypass Switch | Activates the direct input-to-output hard-wire bypass | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | Function Switches | LED indicator for each front-panel switch | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | Power Consumption | 20 Watts | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | Power Connector | IEC receptacle | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | Unit Weight | 5.2 lbs. (2.4 kg) | Shipping Weight | 7.6 lbs. (3.5 kg) |
|
VIRTUALIZER 3D FX2000 - Υψηλής απόδοσης 3D Multi-Engine Επεξεργαστής εφέ.
• 71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
• Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
• Awesome modulation, dynamic, psychoacoustic and EQ algorithms
• Authentic amp simulation, distortion and special effects
• 11 effect combinations with selectable serial / parallel configuration
• Up to 7 adjustable parameters plus 2-band EQ per effect
• 24-bit A/D and D/A converters with 64/128-times oversampling
• True stereo processing for realistic channel separation in stereo image
• 100 factory presets plus 100 user memory locations
• Extensive MIDI implementation
• Accurate LED level meters for perfect level setting and optimum performance
• Servo-balanced XLR and ¼'' TRS inputs and outputs
The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.
The FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.
• Reverbs: Cathedral - Gold plate - Small hall - Studio - Concert - Stage - Spring & Reverse Reverb - Ambience and more...
• Delays: Stereo - Tape Echo - Ping Pong and more...
• Modulation and Pitch Shifter FX: Stereo/Vintage/Jet Stream Flanger - Stereo/Analog/Vintage/Ultra/ Chorus - Stereo/Vintage/Dual Phaser - Rotary - Pitch Shifter - Vibrato and more...
• Dynamic FX: Compressor – Expander – Gated Reverb – An. Compr/Lim. — Ultramizer – Denoiser – De-Esser and more...
• Psychoacoustic FX: Exciter – Enhancer – Stereo Imager and more...
• Filter/EQ FX: Auto/LFO Filter – Parametric/Graphic EQ.
• The FX2000 is also equipped with distortion, amplifier and speaker simulation including Vocal/Tube distortion, Guitar Amp and more...
• Special FX:Vinylizer - Sampler - Vocoder - Voice Canceler - Resonator.
|
DPR-504 Νoise gate τεσσάρων καναλιών |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.