PALMER AUDIO AHMCT8 Cable tester για καλώδια ηχείων και μικροφώνων.

User's Manual

• Solid metal housing
• Powered by a 9-V block battery
• Tests Speakon, XLR, jack/TRS, cinch and midi/DIN cables
• Additional continuity tester with measuring probes
• Optical display and buzzer

Tests XLR, 1/4 in., 1/8 in., TT, RCA and MIDI connectors.

The intelligent, CPU-controlled CT100 accepts virtually any connector type:
XLR, mono and TRS phone (1/4 in., 1/8 in., TT), RCA and MIDI. It shows
which input pin is connected to which output pin. Separate LEDs indicate
proper shield connection and phantom power presence. The CT100 also
offers an installed cable test mode and a continuity check plus a test tone
generator.

Features
3 modes: cable test mode, installed cable test mode, and test tone mode
Accepts XLR, mono and stereo TRS phone (1/4 in., 1/8 in., TT),
RCA and MIDI Connectors
Continuity check
Intermittent detect
Phantom power detect
Grounded shield detect
Test tone generation (1 kHz and 440 Hz)
Battery operation (requires 2 AA alkaline batteries)

Cable Tester ACT-100

The Alphaton active remote cable tester can be used for testing either normal short
cables or long ones, especially mufticores, wkh connectors not being accessible at
one time. The tester is especially suded for fixed installations where cables can not
be tested with a standard type cable tester or Ohm meter. Either symmetric and
unsymmetric cables can be tested.
“Cold" solderings and junction resistances are displayed by color or luminosity changes
in three color LED Display. The imprinted fault table incorporates alt important fault
conditions, indeed not all possible ones due to their reiatively large number. In case the
display is in a state which cannot be found on the imprinted table, it can be looked up in
the user's manual. In any case, however, the cabie is in aquite unusable state and should
be repaired or replaced.The Alphaton cable tester has a SEND and a REMOTE section.
The REMOTE sectionconsistsof two recessed mounted XLR type male or female connector
and a stereo phone jack at the right hand side of the tester. Additionally, a separate REMOTE
plug is delivered togetherwith the active remote cable tester for testing long cables in fixed
installations.

• Measures impedance of speaker lines up to 100k ohms
• Batteries: four (AA)
• Zero adjustment for accuracy on all ranges
• Easy to read meter calibrates directly in ohms
• Includes carrying case, test leads and impedance to power reference chart
• Five year warranty

Digital Sound 8928 SPL Meter with Built-In Measurement Mic - calibrated from 300Hz to 8kHz (+/-2dB), 4 control zones in 10dB steps (40-130dB), large LCD display, peak-hold, fast/slow display modes, includes 9V battery.

A superbly designed easy to use sound level meter with features normally only found on more expensive instruments. It has an electret condenser microphone giving virtually instant readings updated every 0.5 seconds on an extra large LCD display.

• 4 measuring ranges, 40 to 70dB, 60 to 90dB, 80 to 110dB or 100 to 130dB
• 0.1dB resolution updated every 0.5 seconds
• Auto ranging or manual range selection
• ʽAʼ & ʽCʼ frequency weighting
• Fast or slow response filters
• 42mm LCD display with quasi-analogue bargraph and function Indicators
• Bargraph in 1dB steps updated every 40ms
• Max hold function to display the highest recorded value
• Min/max memory since power on or last reset
• Low battery indicator
• Auto power off
• Analogue output AC: 0.707 Vrms (at full scale)
• Supplied with battery

• Microprocessor-controlled cable tester featuring 3 modes: cable and installed cable test plus test tone mode
• Accepts all standard connectors: XLR, Speakon*, TRS (1/4“, 1/8“), RCA, RJ45, MIDI and USB
• Super-easy operation with intuitive LED display
• Continuity check and intermittent contact detection

• Phantom-power and ground-shield check
• Test-tone generator: 1 kHz or 440 Hz at +4 dBu, -10 dBV or -50 dBV
• Operates with 2 AA size batteries (not included)
• Designed and engineered in Germany