| Content |
This low-profile cardioid condenser boundary microphone is recommended for unobtrusive table-, ceiling-, or panel-mount applications in high-quality sound reinforcement, professional recording and teleconferencing. Designed for permanent installation, the microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a cardioid pattern for enhanced gain before feedback and improved signal-to-noise ratio. It is available in two colors: black (ES947) and white (ES947W).
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
- Low-profile element provides uniform cardioid polar pattern with 120º acceptance angle
- Mounts unobtrusively in table-tops, ceilings and wall panels
- Self-contained power module with XLRM-type output connector
- Rugged all-metal case with a two-layer steel mesh grille
- Isolators provide mechanical dampening of mounting-surface vibration
- Requires 11V to 52V DC phantom power
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Available in two colors: black (ES947) and white (ES947W)
- RoHS compliant - free from all substances specified in the EU directive on hazardous substances
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (Cardioid in hemisphere above mounting surface)
- Frequency Response: 40-12,000 Hz
- Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 113 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Weight: 64 g (2.3 oz)
- Dimensions: 69.0 mm (2.72“) long, 30.0 mm (1.18“) diameter
- Output Connector: Integral 3-pin XLRM-type
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
Available Options
MX396C/DUAL Dual-Element 0-180 Degrees, Cardioid, back or bottom exit cable, mute output, LED input
MX396/TRI Dual-Element 90-0-90 mic, adjustable to 120-120-120 degrees, Cardioid, back or bottom exit cable, mute output, LED input
The Microflex® Multi-Element Boundary microphone delivers a unique and versatile tool for conference room installations.
Clean and simple in appearance, Multi-Element Boundary mics come in two or three element configurations, combining the coverage of multiple microphones into one small, compact package.
|
C 547 BL
"Non-crush" case
Inconspicuous
Hypercardioid polar pattern
Easy to repaint
Hypercardioid, studio-quality boundary microphone with rugged, "non-crush" case and
switchable bass-cut filter for reducing footfall noise, ideal for tough on-stage assignments.
Other benefits include optimum acoustic properties, high directivity, and neutral sound.
Having the same frequency response, the C 547 BL can be combined with the CK 47 with
excellent results.
Primarily designed for use in places of worship, theaters, and conferencing, the C 547 BL
is also a good choice for miking kick drums and other instruments.
SPECIFICATIONS:
Polar pattern hypercardioid
Frequency range 30 to 18,000 Hz
Sensitivity 8.5 mV/Pa (-42 dBV)
Max. SPL 133 dB (for 1% THD)
Equivalent noise level 22 dB-A
Signal/noise ratio (A-weighted) 72 dB
Bass filter 12 dB/octave at 150 Hz
Impedance 400 ohms
Recommended load impedance >1000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
Designed to deliver easy, flexible control in conference and boardroom installations, the versatile U891Rx cardioid condenser boundary microphone features a touch-sensitive on-off switch that can be set to three modes: press-on/press-off, press to talk, and press to mute. The phantom-powered microphone is equipped with a unique PivotPoint® rotating output connector and an LED status indicator. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; an 80 Hz low-cut UniSteep® filter reduces pickup of low-frequency ambient noise. The microphone's heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. The unit's self-contained electronics eliminate the need for an external power module.
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 104 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 4 mA typical
- Weight: 264 g
- Dimensions: 108.0 mm long, 84.0 mm maximum width, 23.0 mm height
- Output Connector: TB3M-type
- Cable: 7.6 m long, 3.2 mm diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/ touch-off," "touch-to-talk" and "touch-to-mute“
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U891Rx) and white (U891RWx)
|
Designed for Broadcast, House of Worship, Pro Music, and other applications.
Half-cardioid polar pattern
Boundary layer
Ultra-thin profile (16 mm) housing
Rubber non-slip bottom pad and strong steel screen
Integrated pop filter
Case Material Die cast zinc
Connector Type 3-pin XLR
Element Back Electret Condenser
Finish Non-reflecting Black
Finish White
Impedance, Low-Z balanced 200 Ω
Mic Type Boundary
Open Circuit Voltage 25 mV/Pascal
Polar Pattern Cardioid
Wired/Wireless Wired
Height 16 mm (0.63“)
Width 94 mm (3.7“)
Depth 123 mm (4.84“)
Weight Net 12.63 oz (358 g) | About the AKG Acoustics CBL 410 PCC
The AKG CBL 410 PCC Conference Microphone Set (Black) is a simple to use, plug and play desktop microphone for use with any PC or laptop. It improves audio quality incredibly when making a conference via VOIP. The microphone reproduces the voice with a clear and natural sound.
With its 3.5 mm stereo jack, it is a 100% plug and play device. No drivers are needed. Its ability to be cascaded makes the CBL 410 PCC the perfect tool for modern communication for both single person use in the office and/or multi-person use in a modern meeting room.
This microphone provides optimum intelligibility and audio quality for your meetings. The CBL 410 PCC is also an excellent choice for recording applications.
AKG Acoustics CBL 410 PCC Includes
- AKG 3x CBL 410 PCC PC Boundary Layer Microphones
- GHAP1 USB Adapter
- AKG Warranty
AKG Acoustics CBL 410 PCC Features
- Small and inconspicuous
- Exceptionally rugged
- Excellent sound quality
- High sensitivity
- Low self-noise
AKG Acoustics CBL 410 PCC Specifications
| Polar pattern |
Omnidirectional |
| Microphone Type |
Back electret condenser microphone |
| Frequency response |
50 Hz to 20 kHz |
| Impedance |
2000 ohms ±30% at 1000 Hz |
| Sensitivity |
-42 dB ±3 dB (7.9 mV/Pa)Sensitivity: |
| Maximum current consumption |
0.5 mA |
| Supply voltage |
1.5 to 5 V DC |
| Cable length |
100cm (40“) |
| Connector |
TRS mini jack |
|
Reviews
There are no reviews yet.