BEHRINGER MIC100 TUBE ULTRAGAIN VACUUM TUBE PREAMPLIFIER w-LIMIT

The PRE-73 DLX is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The line and microphone input and the line output are transformer balanced, using three different transformers, each one optimized for its purpose.
This is the way audio components were built before integrated circuits became available. The subjective sound quality delivered by vintage equipment is often prefered over the one delivered by modern units, a situation that is even more obvious now when music is recorded with clean-sounding digital audio equipment.

The circuit used in the PRE-73 DLX is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

FEATURES

- Vintage Style electronics. No intergrated circuits in the signal path.
- Maximum gain on the mic input is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
- Gain range on the Line input: -20 to + 10 dB.
- Switchable impedance on the mic input, 1200 or 300 Ohms, will change the tone of most mics.
- Switchable phantom power and absolute phase.
- A high-impedance instrument input for any sound module, electric guitar or bass.
- A simple but effective 4-step LED output level meter.
- The output level controls makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
- Combo XLR/TRS input jacks and separate output XLR and TRS jacks for flexible connections.
- Insert jack for inserting EQ´s and other units.
- External high power power supply to avoid interaction with the audio circuits and transformers.
- A solid build quality that will last many years of normal use.

The PRE-73 DLX has a number of improvement and new features compared to the PRE-73 MKII:
- Tantalum capacitors in the signal path.
- Selectable 1073-style high pass filter, 50Hz, 80Hz, 160Hz and 300Hz.
- Output Attenuator -7, -14, -21 and -28 dB (located after the output transformer) allows overdriving the output stage and the output transformer for added character by lowering the output signal to a suitable level.
- The circuit board is prepared for Carnhill Mic and Line transformer and high pass inductor.
- The Insert jack can be switched in/out from the front panel. An internal jumper can select that the Insert jack always has an output signal.
- Switchable 600 ohm Output Termination and Ground Lift on the back panel.
- Selectable Active or Passive DI input and selectable input impedance in active mode, Hi Z or 100 kohm, by internal jumpers.
- The DI can signal can be selected to pass or bypass the mic input transformer by internal jumpers.
- Relays are used to control internal switching for DI input, Phantom power, Mic Low Z, Insert and Phase for shorter circuit board signal paths. The relays are controlled by front panel switches.
- Revised gain switch for added headroom.
- Circuit board star grounding scheme.
- Revised power supply with separate regulators for the audio circuits and relay and LED circuits.

Applications

Console input extending for both Digital and Analog mixing
consoles in Studio, Live and Broadcast
Mic Pre-amps for ADAT/ Hard Disk/ Multitrack Recording
 
Innovation
If you love your compact Digital (or Analog) mixing console, but wish it had
more microphone inputs, ARX has the solution ? the 8 Pre: eight channels
of superb sounding Microphone Pre-amps in a compact 1 RU chassis.
The 8 Pre is the ideal console extender for those times when you need more
microphone inputs. Now you can put those unused line inputs to good use,
and who knows - the 8 Pre pre-amps sound so good that you?ll probably end
up using them all the time instead of the ones that came with your mixer!
Superb Audio Quality
The 8 Pre?s ultra low noise figures come from extensive use of premium
components plus care and attention to board design and layout. The result is
superb, transparent audio quality and the headroom to handle anything that a
mic can throw at it.
Gain is adjustable from 20 db through to 60 dB via a trim control on the front
panel, plus we?ve included a ?20dB Pad switch to tame the hottest condenser
mic output if required. The Clip status LED lights up 1 dB before the onset of
clipping, just to warn you you?re getting close.Phantom power is switchable in
banks of four channels: 1 through 4, 5 through 8. A Phase reverse switch is also
provided on each pre-amp channel to eliminate any close miking problems.
In short, the ARX 8 Pre is the mic Pre-amp that you?ll wish the console manufacturer
had used. It provides a unique solution to today?s multiple Mic Pre-amp requirements.

T E C H N I C A L S P E C I F I C A T I O N S
Input Gain 20dB to 60dB
Input Pad ?20dB
Input Impedance 4 KOhm
Input Headroom +23dB
Output Impedance 300 Ohm
Output Level (Max) +23dB
Frequency Response 20Hz ? 20KHz ±0.2 dB
Signal to Noise ratio (Gain set @ 20 dB)
?93dB Unweighted, ?99dB ?A? weighted
Distortion @ Unity Gain .004%, 20 Hz ? 10 KHz
Dynamic Range 116 dB
Phantom Power 48 VDC
Input Connectors Balanced XLR
Output Connectors Balanced TRS jack
Clip Indicator Illuminates 1 dB prior to clipping
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm

The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.

Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel

At PreSonus, weʼve been designing preamps for a long time, and we always focus on audio quality first. So when we decided to upgrade our popular TubePre V2, we focused on improving an already high-quality sound—without jacking up the price. Like the originalTubePre, the new version is a fully professional tube preamp, with a dual-servo (no capacitors) gain stage that lets you boost the program signal to smoking hot levels without significantly increasing the background noise. Discrete components and high-voltage operation offer dynamic range and detail not found in other single-channel tube preamps in its class.

Housed in a rugged case, the TubePre V2 rear panel sports separate unbalanced, ¼” instrument and balanced, XLR mic inputs and unbalanced ¼” and balanced XLR line outputs. Weʼve included all of the extras you need for professional operation including a high-pass filter, phantom power for condenser mics, polarity reverse switch, and a backlit VU meter.

Having had great success with the PRE-73 preamp, we have received many requests for a version for the 500 eries rack format. We are therefore happy to present the PRE-573, expected to start shipping in late September.
 
The PRE-573 is a one width module that has the sound and the features that made the PRE-73 so successful and a few additional ones.
The circuit still uses the preamp and output section from the classic 1073-module, adapted to work in the api rack format. It has a total  gain range from -15 to +80 dB. The 10 - 70 dB range is handled by a turn switch  and there is a separate toggle switch to select an additional 5 or 10 dB gain. The input can be configured to accept line level signals by another switch, the gain is then lowered by about 25 dB and the input impedance increased to about 15 kohm.
 
The input impedance of the mic input mode can be switched between 1200 and 300 ohm. Phantom power and phase reverse is also selectable by front panel switches.
 
An added feature, using the same circuit as in the PRE-73 DLX, is the active DI-input with a high input impedance of about 1,5 Mohm. The output signal from the active DI circuit passes through the input transformer for some extra character.
The DI-input is very flexible since it can be changed to a purely passive one by a front panel switch. The DI input is then exactly the same as in the PRE-73 Mk2 where the signal is feed directly into the second gain stage, bypassing the transformer and with an input impedance of about 100 kohm.

These two DI-options makes it possible to get different tones from electric instruments and the passive DI input mode is more suited for injecting active units like sound modules. 
 
A new feature is the switchable AIR mode that  adds a small boost above 10 kHz that peaks at 2 dB at about 35 kHz.

A simple but effective signal and overload indicator is offered by a single LED that starts glowing red at about +4 dBu and then increases its intensity up to the maximum output level.
 
The PRE-573 has a dedicated insert connector at the back allowing it to interface with other GAP 500 modules. The insert can be activated by removing a jumper connector at the back of the module.
The second Golden Age Project module for the api 500 rack will be the EQ-573, expected to ship in November 2012. The EQ-573 consists of the inductor based high pass filter section  and the 3-band eq section from the classic 1073 module with some added frequencies. These two modules together will offer a fully fledged 1073-module in a compact format at a very low cost.
 
There is a second jumper at the back of the module that selects 600 ohm termination on the output. The standard mode is termination on, since it gives the flattest response when the PRE-573 is used with modern line inputs that typically has an input impedance of 10 kohm or more. The user can chose to remove the jumper and deactivate the termination resistor, this will increase the level above 10 kHz and create a peak in the response for an even more pronounced  "Air" effect.
The output is transformer balanced and fully floating and can drive a 600 ohm load up to level of about 28 dBu.