CAMBRIDGE AUDIO CP2 Phono preamplifier Black

Moving Magnet & Moving Coil Phono Preamplifier

Make the most of any turntable, including the most high-end audiophile models with this Moving Magnet & Moving Coil phono preamplifier.

There's something uniquely pleasurable about listening to vinyl, something that digital media can't reproduce in quite the same way. However most hi-fi amplifiers won't let you plug in a turntable directly. You need to connect via a phono stage (also known as a phono preamp) to make the very small signal from the turntable powerful enough for your main amp to work with. But it's very easy to add noise at this stage, which is why we've designed the CP2 using premium components chosen for exceptional accuracy, amplifying the signal without distorting it.

The CP2 works with all turntables, whichever type of cartridge they use. Like the CP1 it works with popular Moving Magnet cartridges. But it also works with Moving Coil cartridges found in the highest-end audiophile turntables offering even more accuracy and detail than Moving Magnet. Even if your amplifier does have a built-in phono stage, it's well worth bypassing it using the CP2 to deliver much greater depth and detail.

• Phono pre-amplifier with moving magnet (MM) and moving coil (MC) input stages
• Balance control for fine correction of cartridge imbalance
• Discrete transistors for the all-important input stages instead of the more common integrated circuits
• Eco-friendly

• • Ultra-high quality 8-channel A/D and D/A interface for virtually any digital recording/mixing environment
  • 8 state-of-the-art MIDAS designed Mic Preamplifiers
  • Phantom power on all microphone inputs
  • Reference-class Cirrus Logic 24-bit converters for ultimate signal integrity
  • Processes 48 and 44.1 kHz sample rates
  • External sample rate synchronization via word clock or ADAT input

• Optical ADAT in/out interface for ultimate compatibility
• All mic/line inputs routed to the ADAT output
• ADAT input routed to all Line outputs
• “Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
• High-quality components and exceptionally rugged construction ensure long life
• Conceived and designed by BEHRINGER Germany

• Maximum of 66 dB of gain, in eleven discrete steps
• Dynamic range exceeding 120 dB
• 10 Hz to 50 kHz audio bandwidth
• High immunity to RF interference
• High current line output driver
• Transformer-balanced input and output
• Extended range peak limiter via dual opto-isolators makes preamplifier virtually "unclippable“
• Selectable 48-volt / 12-volt phantom power or 12-volt "T" power
• High-pass filter @ 80 or 160 Hz, 6 dB per octave
• Headphone monitoring of microphone audio, monitor audio, or a mix of both
• Monitor input accepts mono, balanced or unbalanced line-level inputs on 1/4-inch tip-ring-sleeve connector
• Separate level control of Monitor gain and overall headphone gain
• Split ear function via DIP switches
• Internal battery power (two-AA)
• Excellent battery life with alkaline and NiMH rechargeable batteries
• External 5-17 VDC powering (plug included)
• High-strength aluminum chassis with durable belt clip

Mic Inputs
• Frequency response at minimum gain (0dB): -0.35dB at 20Hz and –3dB at 122kHz
• Frequency response at maximum gain (60dB): –2.5dB at 20Hz and –3dB 103kHz
• Gain range: 0dB to +60dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +7.4dBu
• THD+N: 0.0009% (measured at 1kHz -20dBu input signal, at 30dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise EIN: -126dB (measured at 60dB of gain with 150Ω termination and 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -98dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 123dB (relative to max output 25dBu)
• SNR: 120dB (relative to 0dBFS (+22dBu)
• CMRR: 88dB.
• Input Impedance, variable: 600Ω, 1400Ω, 2400Ω, 6800Ω

Line Inputs
• Frequency Response at unity gain (0dB): -0.3dB at 20Hz and –3dB at 94kHz
• Gain range: -20dB to +10dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +25.4dBu
• THD+N: 0.002% (measured with +4dBu input signal, 0dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -91dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 116dB (relative to max output 25dBu)
• SNR: 113dB (relative to 0dBFS +22dBu). Input Impedance: 10kΩ

Instrument Inputs
• Frequency Response at +10dB gain: -0.2dB at 20Hz and 0dB at 200kHz
• Frequency Response at +40dB gain: -3dB at 20Hz and –3dB at 38.4kHz
• Gain range: +10dB to +40dB continuously variable
• Maximum headroom: +11.5dBu
• THD+N: 0.006% (measured with –20dBu input signal, at minimum gain (+10dB), with a 20Hz/22kHz bandpass filter)
• Noise at main output with minimum gain (+10dB): -95dBu (measured with a 20Hz/22kHz bandpass filter)
• Input Impedance = >1MΩ

High Pass Filter
• Roll off = 18dB per octave 3 pole filter
• Frequency range: 16Hz to 420Hz (continuously variable, measured at the 3dB down point)

Meters
• 6 LED meter is calibrated 0dBFS = +22dBu (the maximum level which can be correctly converted by the optional internal A/D converter before overload occurs). The meter calibration points are as follows:

Meter panel calibration value in dBFS / Equivalent dBu value
0dBFS / +22dBu
-2dBFS / +20dBu
-6dBFS / +16dBu
-12dBFS / +10dBu
-18dBFS / +4dBu
-42dBFS / -20dBu



Front and rear connectivity

Analogue Channel Inputs (Inputs 1-4)
• 4 instrument 1⁄4” TS jack inputs on front panel
• 4 microphone XLR inputs on rear panel
• 4 line 1⁄4” TRS jacks on rear panel
• 4 insert return 1⁄4” TRS jacks on rear panel
• 4 ADC XLR inputs on rear panel

Analogue Audio Outputs (Outputs 1-4)
• 4 line XLR outputs on rear panel
• 4 insert send 1⁄4” TRS jacks on rear panel

Other I/O
• IEC power input connector 100Vac – 240Vac

Front Panel Indicators
• 8 output meters, 6 segment
• 4 30-60 mic gain range selection indicator
• 4 +48V phantom power indicator
• 4 Phase indicator
• 4 Insert In indicator
• 4 Filter In indicator
• 4 Input selection indicators (Mic, Line, Inst)
• 4 Z In microphone input impedance selection indicators (Low, ISA110, Med, High) Clock select indicators (44.1, 48, 88.2, 96, 176.4, 192)
• Ext clock indicators (Lock, Word clock, 256X)

Weight
5.5kg
12.2lbs

Dimensions (W x H x D)
480mm (W) x 88mm (H) x 280mm (D)
19" (W) x 3.5" (H) x 11" (D)

• 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
• Gain control, 10 steps (6-50 dB)
• Phantom power can be switched on
• Clip LED
• 1 line output, XLR (bal.) or 6.3 mm (unbal.)
• Operation via supplied power unit

The CPR12 is an easy to use, flexible and multifunctional 10 channel pre-amplifier. Six of these input channels are selectable between Mic / Line level and equipped with a 3 band tone control. The first two can be switched to priority and phantom power. The other four channels are direct line inputs.

Every input channel has its own gain and fader volume control with PFL button which makes it possible to pre-listen each input or output channel with the built-in pre-listening speaker, and can be routed to one or both output channels. This makes the CPR12 a full two-zone system.

Other present features are a priority input, a recording output, separate sub-out channels and the 24 V DC emergency power connection. This last feature makes it possible to power the CPR12 with emergency power when the main power is shut down. In this case, the priority input will automatically mute all input signals, and a evacuation message will be announced. The steel 19" housing has a height of 2 HE.

• 10 audio input sources
• 6 Mic / Line inputs with 3 band EQ
• 4 Direct Line Inputs
• Fader volume control
• Two output zones
• Built-in pre-listening speaker
• Priority input for emergency situations
• + 15 V DC Phantom power
• Works on 24 V DC emergency power
  

• Model Name / Type: CPR12 / 10 channel 2 zone pre-amplifier
• THD+N:
• Signal/Noise: > 90 dB
• Frequency Response: 20 Hz - 20 kHz
• Phantom Power: + 15 V DC
• Emergency Power: + 24 V DC
  
• Power Supply: 100 - 240 V AC / 50 - 60 Hz
• Dimensions (W x H x D): 420 x 88 x 320 mm