Content |
Low weight switching final power amplifier. Power 2X2500W / 4Ω, 2Χ3000W / 2Ω. 5000W bridged 8Ω. New integrated BSS OMNIDRIVE 4bit / 192kHz processor with Cirus Logic SHARC A / D and D / A Converters. Level MAX peak voltage and RMS compressing, limiting. New hi-end FIR and IIR filters, 2sec delay / channel, as well as DSP presets for various speakers. LCD display on the front. USB port on the front for loading firmware and Speakers Tunning presets. Analog inputs with XLR, digital input AES / EBU, ethernet input RJ-45 with TCP / IQ protocol. Advanced 3rd generation power supply that allows the amplifier to operate at any voltage. Cooling circuit with microprocessor control with adjustable speed depending on the temperature. Analog and digital outputs (THRU) XLR. Exits speakon 5-way binding post, ground lift switch. Made of cast aluminum, height 2U rack. Suitable for P.A applications but also permanent installations. Weight 10.5kg |
Stereo Mode Ratings (Both Channels Driven):
8 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 1050W
- EIA 1 kHz, 0.1% THD: 1100W
4 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 1600W
- EIA 1 kHz, 0.5% THD: 2000W (1% THD)
2 ohms:
- EIA 1 kHz, 1% THD: 2500W
70V Direct Drive:
- EIA 1 kHz, 1% THD: 2500W
100V Direct Drive:
- EIA 1 kHz, 1% THD: 1000W
Bridged Mono Mode Ratings/Specifications:
8 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 3200W
- EIA 1 kHz, 0.1% THD: 3600W
4 ohms:
- EIA 1 kHz, 1% THD: 5000W
70V Direct Drive:
- EIA 1 kHz, 1% THD: 5000W
100V Direct Drive:
- EIA 1 kHz, 1% THD: 3600W
Signal to Noise, 20Hz-20kHz, 0.1% THD, 8 Ohms: > -100dB
Input Sensitivity @ 8 Ohms: 1.42V (+5.3 dBu)
Voltage Gain @ 8 Ohms: 64x (36 dB)
Output Circuitry: 3-tier Class H
Power Requirements (120V):
- 1/8 power pink noise at 4 ohms: 13.9A
- 1/3 power pink noise at 4 ohms: 26.9A
Power Requirements (230V):
- 1/8 power pink noise at 4 ohms: 7A
- 1/3 power pink noise at 4 ohms: 13.5A
Distortion (SMPTE-IM): |
Business amplifier 2x2000W RMS @ 4 Ohms, 2x2500W RMS @ 2h, 2x1000W @ 100V, bridged (mono) 2400W RMS @ 4 ohms, 3600W / 100V. It has inputs 3-pin XLR, jack 6,3mm (balanced), output speakon and clamp. It also has settings panel dip switches 10 posts (clip limiter, filters, stereo / parallel inputs, bridge mode). Protections turn on / off muting, triac crowbar on each channel, stable performance regardless of load. 3U / 19 "rackmount. Dimensions (HxWxD) 133x483x400mm - 33,1kg.
Characteristics
Power (Stereo Mode):
2x1050W @ 8Ohm (FTC 20Hz- 20kHz, 0,1% THD)
2x1100W @ 8Ohm (EIA 1kHz, 0,1% THD)
2x1600W @ 4Ohm (FTC 20Hz- 20kHz, 0,1% THD)
2x2000W @ 4Ohm (EIA 1kHz, 1% THD)
2x2500W @ 2Ohm (EIA 1kHz, 1% THD)
2x2500W @ 70V (EIA 1kHz, 1% THD)
2x1000W @ 100V (EIA 1kHz, 1% THD)
Power (Bridge Mode):
3200W @ 8Ohm (FTC 20Hz- 20kHz, 0,1% THD)
3600W @ 8Ohm (EIA 1kHz, 0,1% THD)
5000W @ 4Ohm (EIA 1kHz, 1% THD)
5000W @ 70V (EIA 1kHz, 1% THD)
3600W @ 100V (EIA 1kHz, 1% THD)
Signal to Noise, 20Hz-20kHz, 8Ohms:> -100dB
Input sensitivity @ 8Ohms: 1,42V (+5,3 dBu)
Voltage Gain @ 8Ohms: 64x (36dB)
Output Circuitry: 3-tier Class H
Power requirements (230V)
1/8 power pink noise at 4 ohms: 7A
1/3 power pink noise at 4 ohms: 13,5A
Distortion (SMPTE-IM): |
Model T5n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2500
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 5000
8Ω bridge 4400
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 3400
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 6800
8Ω bridge 4400
SN ratio (20Hz-20kHz) 107dB
THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U) |
Info
Professional Power Amplifier 2X1200W/4Ω - Compact size (2-Rack height) - Stable SMPS (Switch Mode Power Supply) applied for low power consumption and low weight - Voltage gain available - High Damping Factor and low T.H.D - Includes clip limiter to prevent a sound crush - For better efficiency, 2-step of H-class AMP accepted - Includes protection circuit to prevent a damage of over heat, short and over voltage - Has 30Hz or 50Hz HPF to protect speaker from low-frequency - 12 Kg
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Ισχύς 2 x 1050 Watt / 8Ω RMS, 2 x 1650 Watt / 4Ω RMS, 3000 Watt / 8Ω bridge RMS. Weight: 13 κιλά.
|
Reviews
There are no reviews yet.