Content | Specifications: • Power output: 3,000 watts 2 ohm stereo per ch, 2,100 watts 4 ohm stereo per ch, 1,200 watts 8 ohm stereo per ch, 4,200 watts 8 ohm bridge-mono, 6,000 watts 4 ohms bridge-mono • Sensitivity (for full rated power at 4 ohms): 1.4V RMS • Frequency response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB • S/N Ratio (below rated 1 kHz power at 8 ohms): 103 dB (A weighted) • T.H.D.: 500 • Crosstalk (below rated power): 20 kHz - 1 kHz: >70 dB • Input impedance (nominal): 20k ohms balanced, 10k ohms unbalanced • Maximum input signal: +22 dBu typical • AC Line voltage and frequency configurations: 120 VAC 60 Hz • AC Line current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 15.3A; no more than 180 watts at idle • Operating temperature: 0°C to 40°C at 95% relative humidity (non-condensing) • Dimensions: 19" W x 3.5" H x 16.2" D • Net weight: 24 lbs. (13.6 kg). |
Dynacord H 5000
The power amp H5000 is part of Dynacord´s new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floatingË switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications.
Dynacord H 5000 features:
2x 1500 Watt / 8 Ohm
2x 2500 Watt / 4 Ohm
2x 3500 Watt / 2 Ohm
Cooling: Front-to-Rear, 5-stage-fans
Dimensions (WxHxD): 483 x 88.1 x 498 mm
Weight: 14.5 kg
Protections:
Audio limiters
High temperature
DC
HF
Short Circuit
Back-EMF
Peak current limiters
Inrush current limiters
Turn-on delay
Mains Circuit Breaker Protection
Mains Overvoltage Protection
|
Business amplifier 2x2000W RMS @ 4 Ohms, 2x2500W RMS @ 2h, 2x1000W @ 100V, bridged (mono) 2400W RMS @ 4 ohms, 3600W / 100V. It has inputs 3-pin XLR, jack 6,3mm (balanced), output speakon and clamp. It also has settings panel dip switches 10 posts (clip limiter, filters, stereo / parallel inputs, bridge mode). Protections turn on / off muting, triac crowbar on each channel, stable performance regardless of load. 3U / 19 "rackmount. Dimensions (HxWxD) 133x483x400mm - 33,1kg.
Characteristics
Power (Stereo Mode):
2x1050W @ 8Ohm (FTC 20Hz- 20kHz, 0,1% THD)
2x1100W @ 8Ohm (EIA 1kHz, 0,1% THD)
2x1600W @ 4Ohm (FTC 20Hz- 20kHz, 0,1% THD)
2x2000W @ 4Ohm (EIA 1kHz, 1% THD)
2x2500W @ 2Ohm (EIA 1kHz, 1% THD)
2x2500W @ 70V (EIA 1kHz, 1% THD)
2x1000W @ 100V (EIA 1kHz, 1% THD)
Power (Bridge Mode):
3200W @ 8Ohm (FTC 20Hz- 20kHz, 0,1% THD)
3600W @ 8Ohm (EIA 1kHz, 0,1% THD)
5000W @ 4Ohm (EIA 1kHz, 1% THD)
5000W @ 70V (EIA 1kHz, 1% THD)
3600W @ 100V (EIA 1kHz, 1% THD)
Signal to Noise, 20Hz-20kHz, 8Ohms:> -100dB
Input sensitivity @ 8Ohms: 1,42V (+5,3 dBu)
Voltage Gain @ 8Ohms: 64x (36dB)
Output Circuitry: 3-tier Class H
Power requirements (230V)
1/8 power pink noise at 4 ohms: 7A
1/3 power pink noise at 4 ohms: 13,5A
Distortion (SMPTE-IM): |
The E Series is a range of lightweight, high-power switch mode amplifiers designed to the highest standards of reliability and sound quality. Developed for the touring market, E Series retain the sonic integrity of the benchmark MC and T Series amplifiers, without the physical weight. The switch mode power supply is capable of delivering high peaks without any perceptible bass 'sag' at very low distortion and is kept within its safe operating area by the new, sophisticated MC² Audio 'intelligent' limiter. The E15, E25, E45 and E4-75 feature MC² Audioʼs proprietary current driven output stages for ultra-high definition sound, delivered over the entire audio bandwidth. The E90 and the E100 are Class D amplifiers designed to meet the demands for higher power with increased efficiency whilst still maintaining the renowned MC² Audio sonic qualities and unsurpassed reliability. All MC² Audio products are covered by a 5 year warranty. Number of Channels: 2 Frequency Response: 20Hz to 20kHz (+/- 0.3dB) Output Power: (per channel) 8 ohms 1250W 4 ohms 2500W 2 ohms 4200W Output Power: (bridged) 8 ohms 5000W 4 ohms 8400W THD%: (@1dB below max output) @ 1kHz 20Hz to 20kHz Gain / Sensitivity: Gain 26/32/33dB Sensitivity (for max power) dBu +15.7/9.7/5.7 (4.7/2.4/1.5V) Power Consumption: Nominal @ 240v into 4 ohms 4.5A Nominal @ 120v into 4 ohms 9.0A Dimensions: (2U) (mm) Amplifier 88(h) x 482(w) x 428(d) Single Box (UK shipping) 230 x 580 x 560 Double Box (outside UK) 250 x 610 x 600 Weight: Amplifier 11.4kg Boxed (shipping weight) 13.4kg User's Manual
|
Crown CDi Series amplifiers are professional tools designed and built for installed sound applications. The series includes four models which are identical except for output power: CDi 1000, CDi 2000, CDi 4000, and CDi 6000. All are rugged and lightweight, and offer unmatched value in their class.
- Extremely versatile; rated for 2-, 4-, 8-ohm loads and 70V and 140V outputs.
- Switch-mode universal power supply.
- Intuitive front-panel LCD screen for quick, easy configuration.
- Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting.
- Up to 20 user defined DSP presets are available.
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. Wide (EIA RS-310-B)
x 3.5 in. (8.9 cm) High x 12.25 in. (31.1cm) Deep
CDi 6000 is 16.2 in. (41.15 cm) deep.
| Net Weight |
CDi 1K, 2K, 4K: 19 lb (8.6 kg).
CDi 6K: 24 lb (10.9 kg).
| Shipping Weight |
CDi 1K, 2K, 4K: 22 lb (10.0 kg).
CDi 6K: 30 lb (13.6 kg).
| |
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
General |
Output power per Channel |
Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
Max output voltage / current |
Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
Current |
|
|
45 Apeak |
AC main power |
Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
Operating voltage |
|
|
90 V – 264 V |
Power consumption / current draw |
Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
THERMAL |
Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
Thermal dissipation* |
Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
Reviews
There are no reviews yet.