Content |
• Professional switched mode power amplifier.
• Strong, rugged steel housing.
• Clear led indicators for status mode, signal input, protection, clip, overheat.
Stereo output power 8 Ohm: 650W (1)
Stereo output power 4 Ohm: 1100W (1)
Stereo output power 2 Ohm: 1500W (2)
Bridge output power 8 Ohm: 2200W (1)
Bridge output power 4 Ohm: 3100W (2)
Frequency response (8 Ohm): 20 Hz- 20 kHz,
+/- 0,5 dB
S/N Ratio: >90 dB
Input sensitivity: 0,775V/1,0V/1,4V
THD+N (8 Ohm,
1 kHz)
¼ Output power: 200
Amplifier: 3 steps Class H
Slewrate: 13V/uSec
Protection circuit: DC/Short circuit
/VHF/Temp
Cooling: Internal heatsink with front to rear airflow
Signal input connectors: XLR 3 pin,
male/female
Speaker output connectors: Binding post,
4 pole speakon
Dimensions (LxWxH): 483 x 500 x 89 mm
Weight: 15,0 kg
(1)The output power is tested conform EIA Standard. (2) The output power is tested conform 1 kHz, 1 x THD, 40 mSec Burst
|
Number of Channels: 2
Output Power: (per channel)
8 ohms 575W
4 ohms 1025W
2 ohms 1750w
Output Power: (bridged)
8 ohms 2050W
4 ohms 3500w
THD%: (@1dB below max output)
@ 1kHz |
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 1600 Watt rms | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | Power output stereo 8Ω: | 2 x 700 Watt rms | | Power output bridged 4Ω: | 3200 Watt rms | | Power output bridged 8Ω: | 2200 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 102 dB | | Crosstalk: | > 65 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 400:1 (8 W) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 20.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Thermal, temperature, direct current, short circuit, RFI | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 16 A | | Power Consumption: | 6500 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 132 / 5.19 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 455 / 17.91 mm/inch | | Net Weight: | 29.5 / 65.03 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 200 / 7.87 mm/inch | | Package width: | 575 / 22.63 mm/inch | | Package depth: | 555 / 21.85 mm/inch | | Shipping Weight: | 32.5 / 71.64 Kg/Lbs |
|
The new flagship of the LX series delivers a mighty 2 x 2100 watts into 2 ohms and 2 x 1500 watts into 4 ohms and therefore has plenty of headroom for large subwoofer arrays. For decades, DYNACORD has been one of the leading manufacturers in the pro audio sector and has established a secure position in the amplifier market thanks to the excellent audio performance,absolute reliability and high stability of the Linear Precision series. With their outstanding operational security, which guarantees years of problem-free use, the amplifiers of the Linear Precision series are now the standard for a wide variety of full-range and multi-way loudspeakers systems in professional venues as diverse as theatres, stadiums, discotheques, clubs and concert halls. Datasheets / ManualsManual (2.2MB)
Load Impedance 2 O, 4 O, 8 O Max. Midband Output Power, THD = 1%, 1kHz 2 O - 2100 W, 4 O - 1500 W, 8 O - 900 W Rated Output Power, THD 300 Slew Rate 38 V/µs Signal to Noise Ratio, A-weighted 108 dB Output Stage Topology Class H Power Requirements 100V, 120V, 220V, 230V, 240 V; 50Hz … 60Hz (factory configured) Power Consumption, 1/8 max. output power @ 4 ohms 1070 W Protection Audio Limiters, High Temperature, DC, HF, Back-EMF, Peak current Limiters Inrush Current Limiters, Turn-On delay Cooling Front-to rear, 3-stage fans Ambient Temperature Limits +5° … +40° ( 40°F … 105°F ) Safety Class I Dimensions ( W x H x D ) mm 483 x 88.1 x 384 Weight 8.70 kg (19.2 lbs) Optional Accessories Rear Rackmount 15.5" D112 930 (RMS15-CL), Rear Rackmount 18.0" D112 933 (RMS18-CL), LPN + Lo-Cut Filter D112963 (NRS 90268)
|
Amplifier Gain 41.5 dB, 35 dB, 32 dB (switchable)
CAN Bus Interface Optional with RCM-26
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 2000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1450 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 850 Watts
Continuous Rated Power
(20-20 kHz, THD |
XR Series - Intelligent Power New Horizons.
A lightweight with enormous power output. Combined with digital signal processing. That's what we call flexibility! Locally controlled or completely networked. No matter what the requirements are. The integrated powerful digital signal processor (DSP) and controller allows for a troublefree and easy adjustment to any acoustical environment. Wear-free digital potentiometers, sequential remote power on, alive contacts for easy supervision, computer controlled monitoring - its enless list of useful feature make it the right choice for any installation. XR - the new definition of Intelligent Power
High Tech SMT Design Digital Signal Processor Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon High-End Switched Power Supply with Power Factor Correction (not XR4000) LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed low noise fans Digital wear-free Volume Controls (can be operated manually) Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Paging Input Monitor Output SXL Dataport Perfect Weight-to-Power ratio 3 Years Warranty
Technical Data: XR 2500: 2x 1600 W @ 2 Ohm 2x 1250 W @ 4 Ohm Class: H Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.02% Signal-to-Noise Ratio: < -106 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 750 to 1200 @ 4 Ohm Cooling: 4 Fans (temp. reg. variable speed) Weight: 9 kg Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“) |
Reviews
There are no reviews yet.