| Content |
• Professional switched mode power amplifier.
• Strong, rugged steel housing.
• Clear led indicators for status mode, signal input, protection, clip, overheat.
Stereo output power 8 Ohm: 650W (1)
Stereo output power 4 Ohm: 1100W (1)
Stereo output power 2 Ohm: 1500W (2)
Bridge output power 8 Ohm: 2200W (1)
Bridge output power 4 Ohm: 3100W (2)
Frequency response (8 Ohm): 20 Hz- 20 kHz,
+/- 0,5 dB
S/N Ratio: >90 dB
Input sensitivity: 0,775V/1,0V/1,4V
THD+N (8 Ohm,
1 kHz)
¼ Output power: 200
Amplifier: 3 steps Class H
Slewrate: 13V/uSec
Protection circuit: DC/Short circuit
/VHF/Temp
Cooling: Internal heatsink with front to rear airflow
Signal input connectors: XLR 3 pin,
male/female
Speaker output connectors: Binding post,
4 pole speakon
Dimensions (LxWxH): 483 x 500 x 89 mm
Weight: 15,0 kg
(1)The output power is tested conform EIA Standard. (2) The output power is tested conform 1 kHz, 1 x THD, 40 mSec Burst
|
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 800W
4Ω EIA 1 kHz 1% THD - 1250W
2Ω EIA 1 kHz 1% THD - 2000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 2600W
4Ω EIA 1 kHz 1% THD - 4000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.92V
32dB Setting - 1.96V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 36.4dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -105dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 12A
230V 50Hz - 7A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
| Crown XTi 4002 Features at a Glance:
* Stereo Wattage: 1600W @ 2 ohms, 1200W @ 4 ohms, 650W @ 8 ohms
* Bridged Mono Wattage: 2400W @ 8 ohms, 3200W @ 4 ohms
* Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
* Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
* 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application
* New system monitoring provides software visibility of AC line voltage and power supply temperature
* Integrated cast-aluminum handles for easy handling and enhanced durability
* Locking power cord clip provides a secure connection between the amplifier and power cord
* Updated HiQnet Band Manager and System Architect control software
* Increased number of presets to a total of 30; 29 of which are user definable |
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 2Ω: | 2 x 1600 Watt rms | | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | | Power output stereo 8Ω: | 2 x 700 Watt rms | | | Power output bridged 4Ω: | 3200 Watt rms | | | Power output bridged 8Ω: | 2200 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | > 102 dB | | | Crosstalk: | > 65 dB | | | Distortion (THD+N): | | | | Intermodulation: | | | | Damping factor: | 400:1 (8 W) | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | | Input impedance: | 20.000 kΩ | | | Controls: | Volume control for each channel | |
| OUTPUT SECTION |
|---|
| Output connector: | 2 x Neutrik Speakon 4 ways | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Two-speed fan | | | Protections: | Thermal, temperature, direct current, short circuit, RFI | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | | Max.current: | 16 A | | | Power Consumption: | 6500 W | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 132 / 5.19 mm/inch | | | Width: | 483 / 19.01 mm/inch | | | Depth: | 455 / 17.91 mm/inch | | | Net Weight: | 29.5 / 65.03 Kg/Lbs | |
| SHIPPING INFORMATION |
|---|
| Package height: | 200 / 7.87 mm/inch | | | Package width: | 575 / 22.63 mm/inch | | | Package depth: | 555 / 21.85 mm/inch | | | Shipping Weight: | 32.5 / 71.64 Kg/Lbs |
| Electro-Voiceʼs new Precision Series Compact amplifiers offer proven Precision Series performance and reliability in a new compact, lightweight format made possible by a highly efficient Class-H design, which generates considerably less heat. The CP3000S is not only the first Precision Series amplifier to use a switch-mode power supply, but also the first switch-mode amplifier with EVʼs Precision Series sound. With up to 2x1600 watts into two ohms, and 2x1100 watts into four ohms, and only 17.96 lbs (8.15 kg it is both powerful and lightweight.
1U Panel w/ 8 XLRM + 8XLRF 2Amplifier Gain 32 dB
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 1600 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1100 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 600 Watts
Continuous Rated Power
(20-20 kHz, THD |
HPS 2500 is a 2 channel power amplifier that delivers up to 2 x 1400 W RMS @ 2 Ω (2800 W RMS bridged @ 4 Ω).
XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.
| Features |
|---|
| Fast response and low distortion | | Easy to configure in stereo / mono / bridge modes | | Extensive protective circuits ensure high reliability and operating safety | | Front panel signal / clip / protect LED indicators | | Minimum load impedance (stereo / mono): 2 Ohm | | XLR input connectors | | SPEAKON output connectors | | 2 unit 19" rack, low weight for easy transportation | | Switchable Limiter |
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 2Ω: | 2 x 1400 Watt rms | | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | | Power output stereo 8Ω: | 2 x 700 Watt rms | | | Power output bridged 4Ω: | 2800 Watt rms | | | Power output bridged 8Ω: | 2200 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | 106 dB | | | Damping factor: | > 300 | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | xlr | | | Input sensitivity: | 1.4 dBm/V RMS | | | Input impedance: | 20 kΩ (balanced), 10 kΩ (unbalanced) kΩ | |
| OUTPUT SECTION |
|---|
| Output connector: | Speakon | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Forced | | | Voltage gain: | 32 – 26 dB | | | Amplifier class: | H | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220 ÷ 240 V (50 / 60 Hz) V ~ Hz | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88/3.4 mm/inch | | | Width: | 482/18.9 mm/inch | | | Depth: | 420/16.5 mm/inch | | | Net Weight: | 19/41,8 Kg/Lbs |
|
Reviews
There are no reviews yet.