Content |
DRIVE RACK PA Complete Equalizaton & Loudspeaker Management System
The DriveRack? PA continues the legacy of DriveRack? series, which has been created by the company that has been redefining the standard of signal processing for more than 30 years. The DriveRack? PA was designed with the purpose and vision of providing state-of-the-art signal processing, while utilizing a simple and intuitive user interface. This goal has been achieved by offering two independent channels of processing power with a linkable 28-Band Graphic equalizer, industry-standard dbx? stereo compressor module, feedback eliminator and the 120A Subharmonic Synthesizer on the input, with a six channel output system that includes parametric EQs, and Peak Plus? limiters (which are used to provide protection against speaker blowouts) and alignment delay. These features combined with the Wizard setup system, represent a methodical design that is guaranteed to deliver optimal, all-inclusive processing in a completely scalable system
* Stereo Feedback Elimination with 12 feedback notch filters * Dual 28-band Graphic EQ * Classic dbx? Compressor * 120A Sub-harmonic Synthesizer * 2x3, 2x4, 2x5, 2x6 Crossover Configurations * Stereo Multi-band Parametric EQ * Stereo Output Limiters * Alignment Delay * Pink Noise Generator * Auto-EQ with 28-band RTA * JBL? Speaker and Crown Power Amp Tunings with Setup Wizard * 25 User Programs/25 Factory Programs * 2 Channel XLR Input and 6 Channel XLR Output * Front panel RTA-M XLR input with phantom power * 24-Bit ADC/24-Bit DAC, >110 dB Dynamic Range * Full Graphic LCD Display
|
The Soundweb London BLU-160 offers configurable I/O, configurable signal processing and a high bandwidth, fault tolerant digital audio bus.
The BLU-160 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette of processing and logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.
This processor features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the distance between devices to over 40km.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-160 to be integrated with GPIO compatible devices. The Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-160 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.
Features - Four Input / Output Card Slots
- Configurable Inputs / Outputs
- Analog Inputs (with Phantom Power per Channel)
- Analog Outputs
- Digital Inputs (AES/EBU and S/PDIF)
- Digital Outputs (AES/EBU and S/PDIF)
- Configurable Signal Processing
- Rich Palette of Processing and Logic Objects
- 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus
- Clear Front Panel LED Indication
- Informative Front Panel Display
- Bi-Directional Locate Functionality
- 12 Control Inputs and 6 Logic Outputs for GPIO Integration
- Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
- HiQnet Device
- Configuration, Control and Monitoring from HiQnet London Architect
|
Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
Power connection: |
Mains input via Coaxial power connector (M) mounting version power supply cord with AC adapter (provided) |
Frequency range: |
10 - 30000 Hz |
THD: |
<0,005 % at 1 kHz |
DSP: |
Digital signal processor |
Impedance: |
Input: 10 kOhm
Output: 50 Ohm |
Gain: |
Output: -50 dB to +12 dB |
Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
Delay: |
0 - 5 ms |
Dynamic range: |
Input: 114 dB
Output: 110 dB |
Sample rate: |
67 kHz |
Connections: |
Input: line via 2 x 3-pin XLR
Output: line via 6 x 3-pin XLR |
Crossover frequency: |
20-20000 Hz |
Max. level: |
Input: +22 dBu
Output: +9 dBu |
USB port: |
Typ B |
PC connect: |
DXO Software via USB, firmware can be updated |
Housing design: |
(19") 48.3 cm rack installation 1 U |
Dimensions: |
Width: 48,3 cm
Depth: 12,8 cm
Height: 4,45 cm |
Weight: |
1,77 kg |
Operating system: |
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better |
| Advanced Feedback Suppression Processor with Full LCD Display
The AFS2 Dual-Channel Advanced Feedback Suppression Processor from DBX protects your ears and audio equipment from annoying and potentially damaging audio feedback without altering your sound. The AFS2 features application-specific filter types for speech, music low, music medium, and music high. The 24 fixed or live narrow-band notch filters are capable of removing frequencies at 1/80 of an octave, ensuring an optimal frequency response without the possibility of feedback.
The front panel features the wizard function to take the guesswork out of setting up any room by incorporating an advanced feedback suppression module and providing a full LCD display for system settings and menus. Additionally, the AFS2 offers a five-segment LED for accurately monitoring input levels for each channel, while the notch filter indicator allows you to monitor the number of filters applied. Dedicated bypass buttons are included to help isolate problem channels. The rear panel offers XLR and 1/4" inputs and outputs, both switchable between +4 and -10 dB operations. A USB port has been provided for firmware updates. The AFS2 ships with a standard IEC power cable.
Number of Channels |
2 |
Inputs |
Connectors: Female XLR and 1/4" TRS
Type: Electronically balanced and unbalanced, RF filtered
Impedance: Balanced 50 kohm, unbalanced 25 kohm
Max Line Level: +20 dBu |
Input CMRR |
>40 dB, typically >55dB @ 1 kHz |
Outputs |
Connectors: Male XLR and 1/4" TRS
Type: Electronically balanced and unbalanced, RF filtered
Impedance: Balanced >120 ohms, unbalanced >60 ohms
Max Level: +20 dBu |
A/D/A Converter |
A/D Converter: DBX type IV conversion system
A/D Dynamic Range: >113 dB A-weighted, >110 dB, unweighted, 22 kHz BW
Type IV Dynamic Range: >119 dB, A-weighted, 22 kHz BW; >117 dB, unweighted, 22 kHz BW
A/D Conversion: 24-bit
Sample Rate: 48 kHz
D/A Dynamic Range: 112 dB A-weighted, 109 dB unweighted
D/A Conversion: 24-bit |
Dynamic Range |
109 dB A-weighted, 106 dB unweighted, 22 kHz BW |
THD + Noise |
0.003% typical at +4 dBu, 1 kHz |
Frequency Response |
20 Hz to 20 kHz, ±0.5dB |
Crosstalk |
Interchannel Crosstalk: >80 dB typical
Crosstalk Input to Output: >80 dB |
Power |
US: 100 to 120 VAC 60 Hz
EU: 220 to 240 VAC 50 Hz
9 W |
Dimensions (HxDxW) |
1.8 x 5.8 x 19.0" / 4.4 x 14.6 x 48.3 cm |
Weight |
4.5 lb / 2.0 kg |
|
The DX 4008 is a complete 4 input - 8 output digital loudspeaker management system designed for the touring or fixed sound installation markets.
The absolute latest in available technology is utilized with 32-bit (40-bit extended) floating point processor and high performance 24-bit Analog Converters. The high-bit DSP prevents noise and distortion induced by truncation errors of the commonly used 24-bit fixed-point devices. A complete set of parameters include I/O levels, delay,polarity, 6 bands of parametric EQ per channel, multiple crossover selections and full function limiters. The DX 4008 can be controlled or configured in real time on the panel or with the intuitive PC GUI accessed via the RS 232 interface. Software upgrade for CPU and DSP via PC keeps the device current with newly developed algorithms and function once available. Multiple setup storage and system security complete this professional package.
Features |
---|
The DX 4008 is a complete 4 input - 8 output digital loudspeaker management system designed for the touring or fixed sound installation markets | Sampling rate can be set to 96kHz | Precise frequency control is achieved with its 1 Hz resolution | Inputs and outputs can be routed in multiple configuration to meet any requirements | The DX 4008 is shipped with a special PC Graphic User Interface (GUI) application - XLink | XLink gives the user an option to control the DX 4008 unit from a remote PC via the RS232 serial communication link | The GUI application makes much easier control and monitor the device, allowing the user to get the whole picture on one screen | Programs can be recalled and stored from/to PC's hard drive, thus expanding the storage to become virtuality limitless |
INPUT AND OUTPUT SECTION |
---|
Input Impendance: | >10 | kΩ | Output Impendance: | 50 | Ω | Maximum Level: | + 20 | dBu | Type: | XLR 3 | Electronically balanced |
AUDIO PERFORMANCE |
---|
Frequency Response: | +/- 0.1 | dB (20 to 20 kHz) | Dynamic Range: | 115 | dB typ (unweighted) | CMMR: | > 60 | dB (50 to 10 kHz) | Crosstalk: | | dB | Distortion: | 0.001% | (1 kHz @ 18 dBu) |
DIGITAL AUDIO PERFORMANCE |
---|
Resolution: | 32 bit | (40-bit extended) | Sampling Rate: | 48 / 96 | kHz | A/D - D/A Converters: | 24 | bit | Propagation Delay: | 3 | ms | No. of Programs: | 30 | |
FRONT PANEL CONTROL |
---|
Display: | 4 x 26 | Character Backlit LCD | Buttons: | 12 Mute Controls 12 Gain / Manu Controls 6 Menu Controls | | “DATA" control: | (dial encoder) | Embedded Thumb Wheel | Level Meters: | 5 | segment LED | Interface | RS 232 | Female DB-9 |
LIMITERS |
---|
Threshold: | -20 to +20 | dBu | Attack Time: | 0.3 to 100 | ms | Release Time: | 2 to 32 | X the attack time |
EQUALISATION |
---|
Type: | Parametric, Hi-shelf, Lo-shelf | 6 per I/O | Gain: | in 0.25dB steps | -30 to +15dB | Bandwidth: | (Q=0.5 to 72) | 0.02 to 2.50 octaves |
CROSSOVER FILTERS |
---|
Filter Types: | Butterworth, Bessel, Linkwitz Riley | | Slopes: | 6 to 24dB/oct (96kHz) | 6 to 48dB/oct (48kHz) |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 | V ~ Hz | Power (consumption): | | mA | Fuse model: | | | Operating temperature range: | 0 ÷ +55 | °C | Operating humidity: | 20 ÷ 90 | % RH non-condensing |
PHISICAL SPECIFICATION |
---|
Height: | 44 / 1.73 | mm/inch | Width: | 483 / 19.01 | mm/inch | Depth: | 203 / 7.99 | mm/inch | Net Weight: | Kg/Lbs | 3 / 6.61 |
SHIPPING INFORMATION |
---|
Package height: | 80 / 3.14 | mm/inch | Package width: | 615 / 24.2 | mm/inch | Package depth: | 360 / 14.17 | mm/inch | Shipping Weight: | 4.3 / 9.4 | Kg/Lbs |
| The LD Systems X223 is a stereo 2 way / mono 3 way crossover in standard 19"/1U rack format. Its rugged construction, high quality and robust knobs as well as the integrated power unit are rarities in this price range. It provides a mono sub output, an adjustable crossover frequency for each channel, adjustable LF/HF and input gains, phase reverse controls, switchable 40 Hz High-Pass filters and symmetrical XLR In- and Outputs. With the LD Systems X223 you get a crossover fulfilling the professional standards and offering great quality and sound characteristics.
Product type
Signal Processors
Version
2-way stereo/3-way mono
Frequency response
20 - 20.000 Hz
Signal-to-noise ratio
> 93 dB
Total Harmonic Distortion (THD)
< 0.004 %
Crosstalk
< - 80 (20 - 20.000 Hz) dB
Max. input level
+21 (balanced or unbalanced) dBu
Max. output level
+21 (balanced or unbalanced) dBu
Input impedance (kOhms)
50000 kOhm
Output impedance
200 Ohm(s)
Controls
2 x crossover frequency low/high, 2 x crossover low/mid, 2 x high gain, 2 x highpass (40 Hz), 2 x input gain, 2 x low gain, 2x frequency switch x1/x10, 4 x inv switch, LF sum, Mono/stereo mode
Indicators
2 x clip, 2 x crossover x 10, 2 x highpass, 4 x inv., mono, stereo
Line input connectors
XLR
Line output connectors
XLR
Mains connector
IEC socket
Operating voltage
220 V AC - 240 V AC
|
Reviews
There are no reviews yet.