EIKON by Proel LCH-100SE Lavalier Mic with 3.5mm jack input

 Shure SLX14 Instrument Wireless System Features:

    SLX4 Wireless Receiver:
    Automatic Frequency Selection
    Automatic Transmitter Setup
    960 Selectable frequencies across 24MHz bandwidth
    Detachable 1/4 wave antennas
    Microprocessor-controlled diversity
    RF presence LED
    5-segment audio meter
    Multi-function, backlit LCD
    Low battery indicator
    Frequency and power lockout
    Rugged metal chassis
    Volume control on rear of unit
    1/2 rack design
    Furnished rack hardware
    Non-slip bumpers for use out of rack
    XLR and 1/4" outputs

    SLX1 Bodypack Transmitter
    Automatic Transmitter Setup
    Backlit LCD with timeout feature
    Frequency and power lockout
    3-segment battery fuel gauge
    2 AA batteries (included) provide 8 hours of continuous use
    518 - 782 MHz operating range



Shure SLX14 Instrument Wireless System Specifications:

    SLX4 Wireless Receiver:
    Audio Output Level (ref. ± 38kHz deviation with 1kHz tone): XLR connector (into 600 Ohm load): —13dBV; 1/4" connector (into 3000 Ohm load): —2dBV
    Output Impedance: XLR connector: 200 Ohms; 1/4" connector: 1kohms
    XLR output: Impedance balanced; Pin 1: Ground; Pin 2: (+); Pin 3: (-)
    Sensitivity: —105 dBm for 12 dB SINAD, typical
    Image Rejection: >70 dB, typical
    Power Requirements: 12—18 Vdc at 150 mA, supplied by external power supply
    Operating Range Under Typical Conditions: 300 ft. (100m)
    Note: Actual range depends on RF signal absorption, reflection, and interference
    Audio Frequency Response (+/— 2 dB): Minimum: 45 Hz: Maximum: 15 kHz
    Note: Overall system frequency depends on microphone element.
    Total Harmonic Distortion (ref. +/— 38 kHz deviation, 1 kHz tone): 0.5%, typical
    Dynamic Range: >100 dB A-weighted
    Operating Temperature Range: —18 degree C (0 degree F) to +50 degree C (+122 degree F)
    Note: battery characteristics may limit this range
    Dimensions (H x W x D): 1.65 x 7.76 x 5.28 in., (42 x 197 x 134 mm)
    Weight: 1 lb. 13 oz. (816 g )
    Housing: Galvanized steel
    Transmitter Audio Polarity: Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with
    respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
    Logic Connections: Pin 1: Logic output, Transmitter Mute Status. Mute=low (0 V). Sinks up to 100 mA. Absolute maximum -0.7 to 5.5V DC; Pin 2: Logic ground; Pin 3: Logic output, Battery Status. Good=low (0 V). Sinks up to 100 mA; Absolute maximum -0.7 to 5.5V DC

    SLX1 Bodypack Transmitter
    Audio Input Level: -10 dBV maximum at mic gain position, +10 dBV maximum at 0 dB gain position, +20 dBV maximum at -10 dB gain position
    Gain Adjustment Range: 30dB
    Input Impedance: 1 Mohms
    RF Transmitter Output: 30 mW maximum (dependent on applicable country regulations
    Dimensions (H x W x D): 4.25 x 2.50 x 0.75 in. (108 x 64 x 19 mmD)
    Weight: 81 grams (3 oz.) without batteries
    Housing: Molded ABS case
    Power Requirements: 2 "AA" size alkaline or rechargeable batteries
    Battery Life: >8 hours (alkaline)

Miniaturized lavalier condenser microphone for wireless or wired applications.

The ADX10 is a miniaturized condenser microphone designed for lavaliere applications such as speech, presentation and theatrical production. The ADX10 has the ability to accurately capture and reproduce vocals from a comfortable distance of 4“- 8“. This mic is clear, resistant to feedback and easy to use.

Designed with a uniformly controlled cardioid polar pattern, the ADX10 helps to isolate the area or section being miked from other vocals or instruments on stage. The ADX10 has a smooth, accurate frequency range of 50 Hz - 18 kHz. This mic is lightweight, low profile and has a natural sound with exceptional sound response.

Primarily for use with the Audix RAD360 Wireless System, the ADX10 includes a tie-clip and a 3' attached cable  terminating to a mini-XLRf connector.

MODEL VARIATIONS:

ADX10P - For hard wired application. Includes an 8' cable terminating to a mini-XLRf connector tie clip, external windscreen and a phantom power adapter module. 9 - 48 V phantom power required.