| Content |
Μίκτης ενισχυτής 240W/100V τεσσάρων ζωνών (4x60W). Διαθέτει εξόδους high impedance και 8Ω, έξοδο pre amp για σύνδεση με εξωτερικό τελικό ενισχυτή, εισόδους πέντε mic/line (κατʼ επιλογή) με priority και phantom power 48V στα mic 1 και 2, gain control σε όλες τις εισόδους, ενσωμετωμένο chime με δύο τόνους, δυνατότητα σύνδεσης με τηλεφωνικό κέντρο και εξωτερικό chime. Κατάλληλο για χώρους που απαιτείται backround μουσικη οπως εμπορικα καταστηματα, κομμωτήρια κτλ
Ισχύς εξόδου (RMS): 240W Ισχύς: 240W/100V τεσσάρων ζωνών (4x60W). Είσοδοι: 5 mic/line (κατʼ επιλογή) με priority και phantom power 48V στα mic 1 και 2 Gain control σε όλες τις εισόδους, Εξοδοι: high impedance και 8Ω, Master volume Ενσωματωμένο chime με δύο τόνους Έξοδο pre amp για σύνδεση με εξωτερικό τελικό ενισχυτή Δυνατότητα σύνδεσης με τηλεφωνικό κέντρο και εξωτερικό chime. Δέχεται module στο front panel CDR-100RDS (radio-cd), TP-100 (tuner FM/AM), DM-100 (digital message) Διαστάσεις (HxWxD) 133x483x350mm Βάρος: 13kg Rackmount 3U
Tεχνικά χαρακτηριστικά
Έξοδοι ηχείων:100V, 70V / 8ohm, 2.6ohm AC Power: 240V, 50Hz DC Power: 24V THD at rated power: 60dB Signal/Noise ratio, Aux: >70dB
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 1000: 2x500 W/100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 33 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Toa A1806 powered mixer is a basic mono/2 zones 60 Watts (100V) PA amplifier with 3 mic channels suited for broadcasting, paging or background music in schools, offices or shops.
| | | Weight (KG) | 9.4 | | Size (mm) | 420 x 107.7 x 367 | | Colour | Black | | Manufacturer warranty (UK) | 1 year RTB |
|
| | - SPEAKER SELECT(5ZONE SPEAKER OUTPUT) Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources. - MONITOR SPEAKER You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - REMOTE CONTROL INPUT Individual speaker zones can be selected and chime can be operated by wired remote control. - EM(EMERGENCY) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE POWER You can turn on/off amplifier by remote control. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities. ACCESSORIES One detachable AC power cord is provided for use with this product. | | | | | | | PAM-510 | PAM-520 | | Amplifier Section (Amp In@1kHz, 4Ω Load Output) | Rated Output Power (THD 1%) | 120W(RMS) | 240W(RMS) | | Speaker Zone 1~5 Output | 25W MAX | 50W MAX | | Input Sensitivity/Impedance | 1V/20kΩ | | S/N | Better than 85dB | | Frequency Response (at 1kHz Half Power Output, ±3dB) | 80Hz~18kHz | | Mic Input Section (Mic 1~4 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Phantom Power | +24VDC | | Line Input Section (Line 1~2 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –30dBV/10kΩ | | S/N | Better than 65dB | | Frequency Response (±3dB) | 80Hz~15kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Remote Amp Section (Remote In@1kHz, Preamp Out) | Mic Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tel In Section (Tel In@1kHz, Preamp Out) | Input Sensitivity/Impedance | 0.3V/600Ω(USA/Canada) | | 0.775V/600Ω(EC & Associated) | | S/N | Better than 65dB | | Frequency Response (±3dB) | 330Hz~3kHz | | Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In) | 0dBV/600Ω | | | T.H.D | Less than 0.5% | | Record Out | –10dBV/3kΩ | | Operating Temperature | –10°C~40°C | | Power Source | 100–120VAC or 220–240VAC; 50/60Hz, 24VDC | | Power Consumption (1/8 POWER) | 180W | 320W | | Weight | 17kg/37.6lb | 19kg/42lb | | Dimensions | 482(W) x 132(H) x 398(D)mm 19(W) x 5.2(H) x 15.7(D)in | | ※ Specifications and design subject to change without notice. | | | |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
| Specification |
|
|---|
| Power Source | 220 - 240V AC or 24V DC | | Rated Output | 240W | | Power Consumption | 238W (EN60065), 520W(AC operation at rated output, 15A (DC operation at rated output) | | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | | Distortion | Under 1% at 1kHz,1/3 rated power | | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:42W (100V)
LOW IMPEDANCE: 4Ω (31V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | | Phnatom Powe | DC + 21V (MIC 1) | | S/N Ratio | Over 60dB | | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | | Indicator | Power signal, peak | | Finish | Panel: ABS resin, black/Case: Steel plate, black | | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | | Weight | 13kg |
|
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with the VP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.
| Power Source | Supplied from VP-2064, VP-2122, VP-2241 or VP-2421 | | Current Consumption | 30 mA or less | | Power Amplifier Link | RJ45 female connector for connecting the VX-200SP,
VX-200SZ Audio Output module, or SX-2100AO.
Twisted-pair straight cable (TIA/EIA-568A standard) | | Finish | Panel: Surface-treated steel plate | | Dimensions | 88 (W) × 25.8 (H) × 53.2 (D) mm | | Weight | 50 g | | Applicable Model | VP-2064, VP-2122, VP-2241, VP-2421 |
|
Reviews
There are no reviews yet.