Content |
The iP 2100 is a space-saving power amplifier, ideal for use in installations as well as in cost-effective live sound systems. The Iron Power (iP) family of power amplifiers is the new compact and versatile line of professional power amplifiers with classic toroidal iron transformers. To achieve a compact design, the latest semiconductor technology is utilized. This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances the 2 ohms capacity. A new Bi-phase wiring scheme also increases the capacity of the power supply. This extends the power bandwidth in the low end.
Key Features: 2 x 425 watts @ 8 ? 2 x 700 watts @ 4 ? 2 x 1050 watts @ 2 ? (Measured just below clip level, with both channels driven) Compact design: 2U high Intercooler? cooling system with front-to-rear airflow Multiple positions gain switch Easily accessible dust filter Improved low-end power bandwidth Neutrik Combo jack and Phoenix terminal block input connectors Bridged mono outputs in one SpeakOn connector
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features to make the iP family functional in all situations from installation to cost-effective live sound systems:
Multiple positions Gain switch To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a multiple position gain switch. The maximum amplifier gain can be set to all industry standards: 20, 23, 26, 29, 32, 35, 38 and 41 dB.
Versatile input connection With the Neutrik Combo-jack we offer both the professional XLR-type standard and the semi-pro 1/4? TRS phono-jacks. For installations the 3-pin Phoenix terminal block may be handier.
Soft Start Toroidal transformers require a huge amount of start current to build up a magnetic flux when the amplifier is switched on. Therefore Lab.gruppen have included a soft start circuit to minimize the risk of blowing the wall fuse and to reduce flickering in the lighting.
Sophisticated protection circuitry, combining: ALStm short circuit protection; the Adaptive Limiting System permits very high peak currents, but keeps the amplifier within the Safe Operation Area. DC protection; protects against infrasonic signals VHF protection; protects the loudspeakers against strong very high frequency non-musical signals above the audible range. Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front panel are switched on, as a warning, before the protection process is initiated. AC protection; shuts down the power supply if the line voltage is outside the operating voltage. Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining full peak power.
|
Crown DSi 2000 2x800W-4Ω Power Amplifier
The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifier shall have the following specifications:
Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm
Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W
with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-
Mono: 1,600W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.09V.
Sensitivity at 4 ohm rated output: 2.84V.
Sensitivity at 2 ohm rated output: 2.24V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.
Maximum Input Signal: +22 dBu typical.
| Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 1800 W, 4 Ω - 1200 W, 8 Ω - 750 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 3400 W, 4 Ω - 1800 W, 8 Ω - 950 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 3600 W, 8 Ω - 2400 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +6.6 dBu (1.66 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class H Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 17.7 kg (39.0 lbs) |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 500W
4Ω EIA 1 kHz 1% THD - 850W
2Ω EIA 1 kHz 1% THD - 1250W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 1700W
4Ω EIA 1 kHz 1% THD - 2500W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.28V
32dB Setting - 1.60V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 34.5dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -106dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 8.5A
230V 50Hz - 7.5A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
The new LD Premium Audio CLASS-H SMPS amplifiers distils all the features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment. In the LD Premium amps, you'll find four 2-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
- Model Name: SP1K8
- Output Power 1 kHz, 500
- Crosstalk (20 Hz - 20 kHz): > 75 dB
- Voltage Gain (selectable): 26/32/38 dB
- Input Sensitivity: 2.6/1.3/0.6 V
- Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICLTM, PMSTM, SSPTM
- Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
- Indicators: Signal, Temperature, ICL (Inteligent Clip Limiting), PMS (Power Management System)
- Connectors:
- Input: 2 x XLR
- Line Output: 2 x XLR
- Speaker Output: 2 x Speakon
- Power Supply: 230 V - 50 Hz
- Dimensions (WxHxD): 483 × 88.9 × 310 mm / 19 × 3.5 ×12.2 inches
| VLP Series Power Amplifier
Output Power:
750W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
500W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
1500W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift / Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 42 lbs. / 19 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter |
Reviews
There are no reviews yet.