Phonic\’s MAX 2500 Power Amplifier provides 1500 Watts of power at 8 ohms (bridge mono) or 750 Watts at 4 ohms (stereo)- ideal for medium to large-size clubs, churches, auditoriums and more. Input to the MAX 2500 amp is achieved via combo connectors that accept both XLR and 1/4\’ jacks, and output is achieved through […]
Phonic\’s MAX 2500 Power Amplifier provides 1500 Watts of power at 8 ohms (bridge mono) or 750 Watts at 4 ohms (stereo)- ideal for medium to large-size clubs, churches, auditoriums and more. Input to the MAX 2500 amp is achieved via combo connectors that accept both XLR and 1/4\’ jacks, and output is achieved through either Speakon?-type connectors or binding posts. The MAX 2500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
Phonic\'s MAX 2500 Power Amplifier provides 1500 Watts of power at 8 ohms (bridge mono) or 750 Watts at 4 ohms (stereo)- ideal for medium to large-size clubs, churches, auditoriums and more. Input to the MAX 2500 amp is achieved via combo connectors that accept both XLR and 1/4\' jacks, and output is achieved through either Speakon?-type connectors or binding posts. The MAX 2500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
Signal and Peak LED indicators to monitor performance
Short circuit, thermal, subsonic, RF protection, output DC offset
Power on/off muting
This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.
A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling. The integral soft clip limiter protects against damage to the connected loudspeakers. The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 2Ω:
2 x 800 Watt rms
Power output stereo 4Ω:
2 x 650 Watt rms
Power output stereo 8Ω:
2 x 350 Watt rms
Power output bridged 4Ω:
1600 Watt rms
Power output bridged 8Ω:
1300 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 103 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
20.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Temperature, DC, RFI short circuit, Soft-Start, Thermal on transformer
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
7.5 A
Power Consumption:
2700 W
PHYSICAL SPECIFICATIONS
Height:
88 / 3.46 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
455 / 17.91 mm/inch
Net Weight:
19.5 / 42.98 Kg/Lbs
SHIPPING INFORMATION
Package height:
150 / 5.9 mm/inch
Package width:
555 / 21.85 mm/inch
Package depth:
525 / 20.66 mm/inch
Shipping Weight:
20 / 44.09 Kg/Lbs
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
OUTPUT POWER
S-1500
S-2000
S-3000
S-4000
S-6000
S-3004
S-4004
S-4044
S-6004
S-6044
1kHz, 1.0% THD
2 ohms
2x880W
2x1190W
2x1570W
2x1950W
2x2950W
4x700W
4x980W
-
4x1440W
-
4 ohms
2x575W
2x790W
2x1100W
2x1380W
2x2025W
4x500W
4x670W
4x975W
4x1000W
4x1480W
8 ohms
2x325W
2x460W
2x630W
2x810W
2x1250W
4x300W
4x430W
4x690W
4x620W
4x1015W
Bridge @ 4ohms
1760W
2380W
3140W
3900W
5900W
2x1400W
2x1960W
-
2x2880W
-
Bridge @ 8ohms
1150W
1580W
2200W
2760W
4050W
2x1000W
2x1340W
2x1950W
2x2000W
2x2960W
P. N. 12dB C.F.
2 ohms
2x975W
2x1360W
2x2060W
2x2460W
2x4225W
4x890W
4x1170W
-
4x2080W
-
4 ohms
2x610W
2x880W
2x1240W
2x1600W
2x2600W
4x580W
4x820W
4x1230W
4x1280W
4x2110W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.28V
32dB Setting - 1.60V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 34.5dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -106dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 8.5A
230V 50Hz - 7.5A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Type
PA Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 800 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 650 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 450 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
1600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
1300 W
Output circuitry
Class H
Frequency response
20 - 20000 Hz
THD
< 0.1 %
Signal-to-noise ratio
106 dB
Damping factor
> 400
Crosstalk
>80 dB
Gain
39 dB
Input sensitivity
0.775 V
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Loudspeaker outputs
2
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Weight
15,9 kg
Features
Volex mains socket
Crown XTi2002 Specifications:
* Output Power 2 ohms Stereo (per ch): 1000W
* Output Power 4 ohms Stereo (per ch): 800W
* Output Power 8 ohms Stereo (per ch): 475W
* Output Power 8 ohms Bridged-Mono: 1600W
* Output Power 4 ohms Bridged-Mono: 2000W
* Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
* Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
* Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
* Total Harmonic Distortion (THD):
* Damping Factor 20 Hz to 1 kHz: > 500
* Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
* Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
* Maximum Input Signal: +22 dBu typical
* Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
* Level Control: Two front-panel rotary level controls, one for each channel
* Power Switch Control: On/Off switch applies AC power to the amplifier
* Sel/Prev/Next Buttons Controls: Three buttons near the LCD screen that are used to access menu items and front panel lockout
* LCD Screen: Backlit liquid crystal display that shows preset and processing status
* Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
* –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
* –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
* Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
* Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
* Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
* Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
* Input Connectors: XLR, one per channel
* Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
* Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
* HiQnet™ USB Connector: Type B, connects to HiQnet™ network.
* Chassis: Steel
* Front Panel: Cast-aluminum
* Cooling: Proportional speed fan with front-to-rear airflow.
* Dimensions: 19" (W) x 3.5" (H) x 12.25" (D)
* Net Weight: 18.5 lbs (8.4kg)
* Shipping Weight: 21.5 lbs (9.8kg)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
![back_s_l](http://"images/ram/back_s_l.jpg“/ "back_s_l")
Reviews
There are no reviews yet.