PRESONUS MP-20 -TWO -CHANNEL MIC PREAMPLIFIER w-STEREO BUS

The MP20 was designed to enhance the performance of any console or digital audio
workstation by providing two very high-end microphone preamplifiers. The MP20 affords
you an amazing choice for the front-end of any analog to digital converter. The MP20
was created utilizing the very best in design parameters and components with a friendly
user interface.
 
 FeaturesTop 
? Class-A Discrete, Dual Servo Microphone Preamplifier
? 20dB Pad
? 48V Phantom
? 80Hz Roll-Off Filter
? Polarity Reverse
? IDSS Control - Creates Vintage Warmth by Adjusting Even Harmonic Distortion.
? 12 Segment Level Meter
? High Output Headphone Amplifier
? Identical Technical Specifications as the M80
? Low Impedance Stereo Mix Bus can be used for Full Control Over Stereo Imaging
? Fully Loaded Back Panel Featuring XLR Balanced I/O Connectors as well as Separate
   Send and Return Jacks for Inserting Dynamics Processors (such as the ACP22)
? 1/4“, High Z Input on the Front Panel for Instrument Preamplification 
? Mix Output Connectors are XLR Balanced Providing Connectivity for Professional 
   Recording Systems

Technical Specifications 
Number of Channels Two
Dynamic Range >120dB
Noise Floor @ Bus -90.2dBu
Noise Floor @ Main Output -96.4dBu
Noise Floor @ Channel Output +24dB gain, -88.2dBu
Headroom +24dBu
Frequency Response +/- 0.5dB, 10Hz - 60kHz
Crosstalk

Mic Inputs
• Frequency response at minimum gain (0dB): -0.35dB at 20Hz and –3dB at 122kHz
• Frequency response at maximum gain (60dB): –2.5dB at 20Hz and –3dB 103kHz
• Gain range: 0dB to +60dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +7.4dBu
• THD+N: 0.0009% (measured at 1kHz -20dBu input signal, at 30dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise EIN: -126dB (measured at 60dB of gain with 150Ω termination and 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -98dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 123dB (relative to max output 25dBu)
• SNR: 120dB (relative to 0dBFS (+22dBu)
• CMRR: 88dB.
• Input Impedance, variable: 600Ω, 1400Ω, 2400Ω, 6800Ω

Line Inputs
• Frequency Response at unity gain (0dB): -0.3dB at 20Hz and –3dB at 94kHz
• Gain range: -20dB to +10dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +25.4dBu
• THD+N: 0.002% (measured with +4dBu input signal, 0dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -91dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 116dB (relative to max output 25dBu)
• SNR: 113dB (relative to 0dBFS +22dBu). Input Impedance: 10kΩ

Instrument Inputs
• Frequency Response at +10dB gain: -0.2dB at 20Hz and 0dB at 200kHz
• Frequency Response at +40dB gain: -3dB at 20Hz and –3dB at 38.4kHz
• Gain range: +10dB to +40dB continuously variable
• Maximum headroom: +11.5dBu
• THD+N: 0.006% (measured with –20dBu input signal, at minimum gain (+10dB), with a 20Hz/22kHz bandpass filter)
• Noise at main output with minimum gain (+10dB): -95dBu (measured with a 20Hz/22kHz bandpass filter)
• Input Impedance = >1MΩ

High Pass Filter
• Roll off = 18dB per octave 3 pole filter
• Frequency range: 16Hz to 420Hz (continuously variable, measured at the 3dB down point)

Meters
• 6 LED meter is calibrated 0dBFS = +22dBu (the maximum level which can be correctly converted by the optional internal A/D converter before overload occurs). The meter calibration points are as follows:

Meter panel calibration value in dBFS / Equivalent dBu value
0dBFS / +22dBu
-2dBFS / +20dBu
-6dBFS / +16dBu
-12dBFS / +10dBu
-18dBFS / +4dBu
-42dBFS / -20dBu



Front and rear connectivity

Analogue Channel Inputs (Inputs 1-4)
• 4 instrument 1⁄4” TS jack inputs on front panel
• 4 microphone XLR inputs on rear panel
• 4 line 1⁄4” TRS jacks on rear panel
• 4 insert return 1⁄4” TRS jacks on rear panel
• 4 ADC XLR inputs on rear panel

Analogue Audio Outputs (Outputs 1-4)
• 4 line XLR outputs on rear panel
• 4 insert send 1⁄4” TRS jacks on rear panel

Other I/O
• IEC power input connector 100Vac – 240Vac

Front Panel Indicators
• 8 output meters, 6 segment
• 4 30-60 mic gain range selection indicator
• 4 +48V phantom power indicator
• 4 Phase indicator
• 4 Insert In indicator
• 4 Filter In indicator
• 4 Input selection indicators (Mic, Line, Inst)
• 4 Z In microphone input impedance selection indicators (Low, ISA110, Med, High) Clock select indicators (44.1, 48, 88.2, 96, 176.4, 192)
• Ext clock indicators (Lock, Word clock, 256X)

Weight
5.5kg
12.2lbs

Dimensions (W x H x D)
480mm (W) x 88mm (H) x 280mm (D)
19" (W) x 3.5" (H) x 11" (D)

 The OctaMic II provides 8-Channel 192 kHz / 24 bit AD conversion with eight hi-class microphone and line pre-amplification channels, featuring a combination of sophisticated components and approved RME technology.

Lowest distortion, excellent signal to noise ratio and perfectly linear frequency response transmit and amplify the microphone signals truly unchanged.

The OctaMic II includes some significant enhancements compared to the OctaMic:

The balanced TRS inputs of the Neutrik Combo XLR jacks are phantom power-free and can be operated as real line inputs too. The improved design of the input circuits allows for a maximum input level of +21 dBu with a convenient gain range from 6 dB up to 60 dB.
Improved signal to noise ratio (SNR) ADC 107.5 dB
Improved THD, especially at higher gains
Optimised heat dissipation by a new and larger housing with improved convection
Internal wide range power supply with line filter, insensitive to voltage fluctuations
Super-stable, short circuit proof 48 V phantom power


Features

OctaMic II offers 8 balanced XLR mic / line inputs via Neutrik XLR/TRS combo jacks. Each channel contains switches for 48V phantom power, a low cut filter and phase reversal. Amplification can be set between 6 and 60 dB. LEDs for signal, clip, and activated phantom power give a complete overview on the unit's status. When the special Clip Hold mode is activated, any detected clip-state will cause the corresponding LED to flash once per second. With this, the user gets a long-term peak detection, and no longer needs to constantly watch the LEDs. At the same time momentary overloads are still displayed correctly.

Frontside switches include power on/off and output level, for a choice of -10 dBV, +4 dBu or Hi Gain (+19 dBu) as reference level. This unusual feature offers two advantages. First, the reference level can be easily switched to match any of RME's current interface devices, from HDSP 9632 through Multiface up to the renowned ADI-8 series converters. Second, the Signal to Noise ratio is optimized, and the Clip-LED will exactly match the ones of the ADI-8 (2 dB below 0 dBFS).

The balanced line level output signal is available at the back of the unit via 8 stereo TRS jacks. The specially developed, internal hi-performance switch mode power supply lets the OctaMic II operate in the range of 100V to 240V AC. It is short-circuit-proof, has an integrated line-filter, is fully regulated against voltage fluctuations, and suppresses mains interference.

Top
AD-Conversion

The 8-Channel AD-conversion of the OctaMic II operates at up to 192 kHz. The digitized signal is available simultaneously at the double ADAT output (S/MUX, up to 96 kHz), and at a DB-25 connector (4 AES/EBU outputs, up to 192 kHz). The digital part can be clocked internally (master) and externally via word clock, AES/EBU and SPDIF.

RME's outstanding SteadyClock(TM) ensures perfect AD-conversion, as jitter on the external sync-sources is nearly completely removed. All settings are done via DIP-switches on the back of the OctaMic II. Analog outputs and both digital outputs operate fully simultaneously. The choice of reference level affects the analog outputs only, the signal/clip indication and the AD-conversion will react only to the Gain-pots.


Top
Tech Specs

8 balanced XLR/TRS mic/line inputs

54 dB gain range

Input impedance: XLR 2 kOhm, TRS 5 kOhm

Analog input level: from -40 dBu up to +21 dBu

Maximum output level: +21 dBu

Output impedance: 75 Ohm

Output level switchable Hi Gain / +4 dBu / -10 dBV

Signal to noise ratio (SNR): 129 dB EIN @ 150 Ohm

THD:
Large frequency range (200 kHz) with special EMI input filtering

Frequency response -0.5 dB: 5 Hz - 200 kHz

Hi-pass filter: 80 Hz, 18 dB/oct.

Line Out: 1/4" TRS (6.3 mm stereo jack), servo-balanced

Phantom power: +48 Volt switchable per channel

Internal wide range switching power supply 100-240 Volt AC

Unbeatable price/performance ratio!

AD conversion

SNR: >110 dB(A)

Supported sample rates: 28 kHz - 200 kHz

THD:
Sync Sources: AES/EBU (also SPDIF coaxial), wordclock, internal

SteadyClock(TM) ensures best sound quality even with jittery external clocks


Top
Accessories

Digital breakout cable Pro, AES/EBU, D-sub25 to 4x XLR-3 female + 4x XLR-3 male, 1m/3m/6m (ALVA Audio)
Digital D-sub cable, AES/EBU, D-sub25 male to D-Sub25 male, 1m/3m/6m (ALVA Audio)
Optical ADAT Toslink cable 1m/2m/3m/5m/10m (ALVA Audio)
Word Clock cable, 1 x BNC male to 1 x BNC male, 1m/5m/10m (ALVA Audio)

Top
Add-On

BOB-32    Universal Breakout Box with 2 x 8 XLR to 2 D-sub connectors (supports TASCAM and YAMAHA format), flip-frame case

Features
Superlative sound
Studio quality mic preamp
Total control - Input Gain, EQ contour, Output Gain,
Overload indicator
Multiple output connectors
XLR/jack combo input 
Switchable 48 V DC Phantom Power for condenser Mics
Compact, computer friendly package
Needs no external power supply
 
ARX is proud to introduce the e-pre - the ultimate microphone pre-amp for
hard disk recording, designed by audio professionals, not computer engineers.
The all-new e-pre is so much a part of your system that it fits right into a spare
5?" slot in your computer case! It's the perfect tool for all your day-to-day
recording requirements. No equipment racks to plug in, no masses of cabling to
connect - the e-pre is ready and waiting when you need it.
The e-pre is a studio quality microphone pre-amp using the same internal components
as high end mixing consoles, built into a compact, computer friendly package.
It has controls for:
Input Gain - fully variable from 10dB through to 60dB to suit all types of microphones,
plus switchable 48 V Phantom Power to enable condenser microphones to deliver
their best.
A Contour control for EQ sweetening, providing fast, easy access to a whole range
of useful EQ curves
Output level control - fully variable to match the e-pre's output to the input of the sound
card. From -10dB consumer cards through to +4dB for professional sound cards, the
e-pre can handle it.
Multiple output connectors match up with any kind of sound card, including mini jacks,
standard jack, RCA (phono) plugs, and even a connector to link to the internal CD ROM
audio input of your sound card (if fitted).
We've even fitted a 12 VDC input connector on the rear to enable the e-pre to run from an
external power supply if required (eg for use with notebook computers or stand-alone use).

Any way you look at it, the e-pre by ARX is the total professional microphone pre-amp for
all your hard disk recording needs

e-pre Benefits
Professional Balanced XLR mic input
True 48v phantom power
Runs into the Line input of ANY sound card - uses the card you've already paid for
High headroom = clean recordings
Smart EQ
Compatible with non-computer audio equipment
Professional performance and specs in a user friendly package
 

T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance
Mic 2 K Ohms Balanced; XLR type Pin 1 Audio Ground, Pin 2 +, Pin 3-
Line 25 K Ohms Balanced, ?" TRS jack Tip +, Ring , Sleeve Audio Ground
Phantom Power Voltage Switchable +48 V DC on XLR Pins 2 and 3
Max Input Level Mic +15 dB, Line +20 dB
Input Gain 10 dB Minimum, variable to 60 dB Maximum
Output Level -10 dB variable through 0 dB to +4 dB
Overload Indicator Measured at all Gain points throughout the circuitry
Output Noise -90 dB Unweighted, -97 dB 'A' weighted
(Measured with Gain nominal 20 dB, Output level -10 dB)
Frequency Response 20 - 20 KHz ± 0.25 dB
Distortion
100 Hz 0.0085%
1 KHz 0.008%
10 KHz 0.0083%
(Measured with Mic Gain 20 dB, Output 0 dB)
Power Requirements 12 V DC from either computer supply or external supply
(external power supply not included in e-pre package)
Size 148mmW x 42mmH x 150mm D (5?“W x 1?H x 6“D)
Weight Under 1 Kilo (2.2 lbs)
 

The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.

The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.

The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.

The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.

The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.

The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.

The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
-  LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme.