| Content |
The new Stereo VideoMic Pro provides a high quality stereo option for videographers, and is ideal for recording music, and the atmospheric ambience essential in building a realistic audio scene.
The new Stereo VideoMic Pro provides a high quality stereo option for videographers, and is ideal for recording music, and the atmospheric ambience essential in building a realistic audio scene. Based around the all new capsule with its matched pair of high sensitivity ½”cardioid condensers in a coincident XY pair, the Stereo VideoMic Pro provides a wide stereo image with natural depth.
Another new addition is the integrated Rycote® Lyre® based shock mounting system, which separates the Stereo VideoMic Pro capsule and electronics from its mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone. Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.
The Stereo VideoMic Pro, with its ergonomic form factor, make it perfectly suited to DSLR, consumer camcorders and large-sensor video cameras. The newly designed Kevlar reinforced braided cable, as well as the improved foam windscreen, provides excellent acoustic decoupling from the camera and offers significantly lower noise transference and higher sensitivity.The user friendly designed rear of the microphone body features the power and equalisation controls, including a high pass filter at 75Hz which is designed to cut out the noise generated by air conditioning, traffic and other undesirable low frequency interference.
A -10dB PAD allows the user to reduce the sensitivity of the microphone, making it suitable for recording loud sound sources such as live music or at sporting events. Like the VideoMic Pro, the Stereo VideoMic Pro features a +20dB level boost specifically designed to provide a higher quality signal with DSLR cameras. When activated, the typically low quality camera preamp level can be reduced, resulting in a lower noise floor and much clearer recording. The RØDE Stereo VideoMic Pro is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
| Type: | Condenser Microphone | | Pick Up Pattern: | Cardioid | | Frequency response: | 40Hz - 20kHz | | Sensitivity: | -38.0dB re 1 Volt/Pascal (12.60mV @ 94 dB SPL) +/- 2 dB @ 1kHz | | Ιmpedance: | 200Ω | | Τotal harmonic distortion: | - | | Dimensions: | 134mmH x 80mmW x 115mmD | | Weight: | 116 gr |
| The R?DE VideoMic is a professional grade shotgun microphone. Based on the
latest ?Film industry? technology, the VideoMic is designed specifically for use with
high quality Digital Video Cameras.
The microphone exhibits low noise and an unusually wide bandwidth for its size. It
is ultra lightweight, yet rugged due to it?s ABS construction. The VideoMic is powered
by a standard 9 V battery and offers a Low Battery LED status indicator and a
switchable high pass filter to reduce unwanted low frequency rumble.
The VideoMic attaches to any Camcorder that has the standard camera-shoe fitting
and utilizes a stereo mini jack for audio output.
SPECIFICATIONS:
Features:
Studio recording quality. Rugged fibre-reinforced ABS construction. 9 V battery operation.
Custom designed integral wind shield. Condenser Microphone. Low noise circuitry. Low
handling noise. Integral camera-shoe mount. Designed & manufactured in Australia.
Full 2 year guarantee.
Operation power:
The VideoMic is designed to operate from a 9 V battery (ANSI:1604A or IEC:6LR61).
The battery is conveniently located within the support arm of the microphone. A fully
removable access cover and a 1-way insertion mechanism ensure ease of loading.
The battery will provide more than 100 hrs. of continuous use due to a low consumption
of only 5.0 mA.
Operation output impedance:
The microphone will operate satisfactorily into a load impedance as low as 1 k?.
If a load below this is used, the output signal level will be reduced.
Acoustic principle: Line plus Gradient
Directional pattern: Super-Cardioid
Frequency range:
40 Hz ~ 20 000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
74 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 20 dB SPL (per IEC651, IEC268-15)
Maximum spl: 134 dB (@ 1% THD into 1 kΩ)
Sensitivity:
-38 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 114 dB (per IEC651, IEC268-15)
Power supply voltage:
9 V DC Alkaline Battery (ANSI:1604A or IEC:6LR61)
Current consumption: 5 mA
Battery life: >100 hours
Output connection: Stereo mini jack plug - ?3.5 mm.
Weight: 176 grm.
Dimensions width: 250mm
Dimensions depth: 65mm
Dimensions height: 102mm |
The new RODE NTG-2 is a lightweight condenser shotgun microphone, designed
for professional applications within the film, video, television and production industries.
The NTG-2 provides a balanced low impedance output stage and operates either
from an internal 1.5 V battery (AA) or 48 V to the P48 standard. A wide bandwidth
and controlled polar response coupled with low noise SMT electronics, makes the
NTG-2 the perfect choice for film, video engineering and voice-over work. The NTG-2
is extremely lightweight making it ideal for mounting directly to video cameras or on
boom poles.
The NTG-2 comes complete with mount and windshield.The windscreen effectively
suppresses wind noise when recording outdoors in moderate conditions.
SPECIFICATIONS:
Features:
Broadcast sound quality. Rugged metal construction. Condenser microphone transducer.
Weighing 161 grams approx. . Low noise circuitry. Low handling noise. Supplied with stand
mount and zip pouch. Designed & manufactured in Australia. Full 2 year guarantee.
Operation power:
The NTG-2 is designed to operate from standard P48 phantom power or a 1.5 V Alkaline Battery.
The NTG-2 will operate between 44 V to 52 V applied with positive polarity to pin 2 and pin 3 via
the output XLR connector.
Operation output impedance:
The NTG-2 will operate satisfactorily into a load impedance as low as 1 k§?. If a
load below this is used, the output signal level will be reduced. The NTG-2??s
output is balanced between pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Line plus Gradient.
Directional pattern: Super-Cardioid.
Frequency range:
20 Hz ~ 20 kHz selectable HPF @ 80 Hz/12 dB octave
Output impedance: 250 ? - phantom power, 350 ? - battery power
Signal noise ratio din iec 651:
76 dB (1 kHz rel. 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 18 dB SPL (per IEC651, IEC268-15)
Maximum spl: 131 dB (@ 1% THD into 1 k?)
Sensitivity:
-36 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 113 dB (per IEC651, IEC268-15)
Power supply voltage: 1.5 V Alkaline Battery or P48 Phantom
Current consumption: 2.0 mA
Battery life: >400 hours with fresh alkaline battery.
Output connection:
3 pin XLR, balanced output between pin 2(+), 3(-) and Pin 1 (ground)
Weight with battery: 161 g approx.
Dimensions width: 278 mm
Dimensions depth: 22mm
Dimensions height: 22mm
|
Audio-Technica's AT897 is designed for field audio acquisition in film/TV/video production, professional recording, wildlife recording and broadcast applications. It mounts conveniently on a DV camcorder without adding noticeable heft, and remains out of the frame even with compact digital cameras. This high-performance short shotgun offers outstanding long-distance audio pickup due to narrow acceptance angle of line + gradient design. It also features smooth, natural-sounding on-axis audio quality and excellent off-axis rejection of sound arriving from the sides and rear of mic.
Designed for video production and broadcast (ENG/EFP) audio acquisition
Short length (11“) ensures mic stays out of the shot -- even when used with compact digital cameras
Smooth, natural-sounding on-axis audio quality
Provides the narrow acceptance angle desirable for long-distance sound pickup
Excellent sound rejection from the sides and rear of mic
Switchable low-frequency roll-off
Operates on battery or phantom power
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Line + gradient
Frequency Response: 20-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Phantom: -40 dB (10.0 mV) re 1V at 1 Pa Battery: -41 dB (8.9 mV) re 1V at 1 Pa
Impedance: Phantom: 200 ohms Battery: 300 ohms
Maximum Input Sound Level: Phantom: 129 dB SPL, 1 kHz at 1% T.H.D. Battery: 115 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 112 dB, 1 kHz at Max SPL Battery: 98 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 77 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Flat, roll-off (recessed)
Weight: 5.1 oz (145 g)
Dimensions: 10.98" (279.0 mm) long, 0.83" (21.0 mm) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; AT8134 windscreen; battery; 5/8“-27 to 3/8“-16 threaded adapter; protective carrying case
|
ProMic Laser is our first ever DSLR on-camera microphone - a shotgun condenser microphone with a precision-tuned capsule for capturing professional-quality audio direct to camera.
With more and more video recording enthusiasts taking an increased interest in the quality of the audio of their videos, ProMic Laser provides the high-quality audio to match the high-definition video capabilities of todayʼs DSLR cameras.
Laser, the first release in the ProMic series, is a truly professional solution. It has a rugged aluminium design and comes with a removable wind shield and a custom shockmount for hot-shoe mounting directly onto a DSLR camera.
Laser is battery-powered using a single AAA battery (not included), which means that the microphone has an increased sensitivity level, and a lower noise floor, but the inclusion of a -10dB Pad allows you to reduce the level of the mic for recording louder sources.
The microphone also features a Bass Cut, which gives you the option of removing unwanted low frequency rumble, such as traffic or noise from the camera itself, and this can be used in tandem with the -10dB Pad.
As with all sE Electronics products, ProMic Laser comes with a three-year free replacement warranty, which means if it lets you down, weʼll simply give you a new one.
ProMic Laser comes with a protective carry bag and a 3.5mm coiled jack-to-jack cable to connect the microphone to your camera. Laser is compatible with the upcoming ProMic accessories series, which includes boom poles and fur windshields. |
Broadcast sound quality
Low noise circuitry
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
Ten year extended warranty with online registration
The NTG4 builds on the platform created by RØDE's award-winning NTG1 shotgun microphone. A broadcast-quality directional condenser microphone designed to provide premium audio recording in a versatile range of applications including on-camera and boom mounted.
Visit the NTG4 feature page
NTG4 Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom power
Weight 126gm
Dimensions 225mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration
|
Reviews
There are no reviews yet.