Content |
The e 912 is a pre-polarized condenser boundary microphone with
half-cardioid pick-up pattern. Its acoustic properties have been
optimized for instruments, vocals and speech. The e 912 is an ideal
choice for pianos, theatre and opera productions, conference applications,
altars and lecterns.To optimally match the installation environment,
the e 912 is available in black or creme white.
Features
Frequency response and sensitivity optimized for picking up instruments,
vocals and speech
Unobtrusive, flat housing
Extremely rugged and step-resistant
Shock-absorbing rubber base
Mounting slots for table installation
Gold-plated XLR connector
Integrated pre-amp
Delivery Includes
e 912 Microphone
Pouch
User manual
Technical Data
Transducer principle (Microphone) permanently polarized condenser
Pick-up pattern half-cardioid
Sensitivity in free field, no load (1kHz) 10 mV/Pa
Max. Sound pressure level (aktiv) 135,6 dB
Equivalent noise level 26 dB(A)
Phantom powering 48 V / 1,1 mA
Nominal impedance
Min. terminating impedance 1000 Ohm
Dimensions 126,5 x 105 x 26,5 mm
Weight ca. 550 g
| The PRO42\'s low-profile design assures inconspicuous appearance for surface-mount use in boardroom, school, government, house of worship and other installed applications. Designed for sound reinforcement, broadcasting and recording applications, the PRO42 brings crisp, intelligible audio reproduction to the podium, stage, conference table and beyond. With a wide-range condenser element and low-mass diaphragm for superior performance, the microphone is equipped with self-contained electronics, eliminating the need for external power modules.
Very low-profile design for minimum visibility
Wide-range condenser element with low-mass diaphragm for superior performance
Uniform polar pattern for maximum rejection of unwanted sounds
Rugged design and construction
25\' (7.6 m) cable permanently attached between microphone and XLRM-type connector
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
Frequency Response: 70-14,000 Hz
Open Circuit Sensitivity: -38 dB (12.5 mV) re 1V at 1 Pa
Impedance: 100 ohms
Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 105 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 9-52V DC, 2 mA typical
Weight: 1.2 oz (35 g)
Dimensions: 1.44" (36.6 mm) maximum width, 2.14" (54.3 mm) maximum length, 0.61" (15.5 mm) height
Output Connector: 3-pin XLRM-type on cable
Cable: 25\' (7.6 m) long, permanently attached | About the AKG Acoustics CBL 410 PCC
The AKG CBL 410 PCC Conference Microphone Set (Black) is a simple to use, plug and play desktop microphone for use with any PC or laptop. It improves audio quality incredibly when making a conference via VOIP. The microphone reproduces the voice with a clear and natural sound.
With its 3.5 mm stereo jack, it is a 100% plug and play device. No drivers are needed. Its ability to be cascaded makes the CBL 410 PCC the perfect tool for modern communication for both single person use in the office and/or multi-person use in a modern meeting room.
This microphone provides optimum intelligibility and audio quality for your meetings. The CBL 410 PCC is also an excellent choice for recording applications.
AKG Acoustics CBL 410 PCC Includes
- AKG 3x CBL 410 PCC PC Boundary Layer Microphones
- GHAP1 USB Adapter
- AKG Warranty
AKG Acoustics CBL 410 PCC Features
- Small and inconspicuous
- Exceptionally rugged
- Excellent sound quality
- High sensitivity
- Low self-noise
AKG Acoustics CBL 410 PCC Specifications
Polar pattern |
Omnidirectional |
Microphone Type |
Back electret condenser microphone |
Frequency response |
50 Hz to 20 kHz |
Impedance |
2000 ohms ±30% at 1000 Hz |
Sensitivity |
-42 dB ±3 dB (7.9 mV/Pa)Sensitivity: |
Maximum current consumption |
0.5 mA |
Supply voltage |
1.5 to 5 V DC |
Cable length |
100cm (40“) |
Connector |
TRS mini jack |
|
A wide range condenser microphone with a cardioid polar pattern, the ultra-smart U891RCx is equipped with local or remote switching options. For flexible control in conference and boardroom installations, the unit's external contact closure ability allows a user to trigger an external device - a camera, for instance - from a switch on the microphone. Another ease-of-use feature: the microphone's electronic on-off switch can be set to three operating modes: touch-on/touch-off, press to talk, and press to mute. The mic is also equipped an 80 Hz low-cut UniSteep® filter to reduce pickup of low-frequency ambient noise. Its red LED status indicator can be controlled remotely. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; a unique rotating PivotPoint® connector changes the cable exit point - no tools required. It requires 11 to 52V DC phantom power, which operates the microphone and switch circuitry.
- Designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup situations
- Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/touch-off," "touch-to-talk" and "touch-to-mute“
- External contact closure capability permits control of remote devices from microphone switch
- External LED control allows for accurate depiction of the live status of the microphone
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 104 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 4 mA typical
- Weight: 266g
- Dimensions: 108.0mm long, 84.0mm maximum width, 23.0mm height
- Output Connector: TB5M-type
- Cable: 7.6m long, 3.2mm diameter, 5-conductor shielded cable (2 conductors under shield; 3 control wires outside shield); TA5F-type connector at microphone end, output end stripped and tinned for connection to electronic device
|
The new Engineered Sound.
This low-profile omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording and teleconferencing in table-, ceiling-, or panel-mount applications. The microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. The microphone offers unsurpassed immunity from radio frequency interference thanks to Audio-Technica's UniGuard® innovations. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a 360º pickup angle, and is available in two colors: black (ES945) and white (ES945W).
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
- Low-profile element provides uniform omnidirectional polar pattern with 360º acceptance angle
- Mounts unobtrusively in table-tops, ceilings and wall panels
- Self-contained power module with XLRM-type output connector
- Rugged all-metal case with a two-layer steel mesh grille
- Isolators provide mechanical dampening of mounting-surface vibration
- Requires 11V to 52V DC phantom power
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Available in two colors: black (ES945) and white (ES945W)
- RoHS compliant-free from all substances specified in the EU directive on hazardous substances
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Omnidirectional
- Frequency Response: 40-18,000 Hz
- Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 112 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 64 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Weight: 63 g (2.2 oz)
- Dimensions: 69.0 mm (2.72“) long, 28.0 mm (1.10“) diameter
- Output Connector: Integral 3-pin XLRM-type
|
SHURE MX-391/C Microphone BOUNDARY
Microflex Boundary There's never been smarter boundary microphones than the Microflex models from Shure. With many models to choose from, equipped with features like programmable, silent membrane switches, logic inputs and outputs, and LED indicators, Microflex Boundary microphones are the high-quality solution for a range of applications, such as altars, boardrooms and distance learning centers. Every Microflex Boundary microphone features one of the new interchangeable condenser cartridges. Available in cardioid, supercardioid and omnidirectional polar patterns, the Microflex cartridges give you superior Shure quality sound options for every installation. In addition, their programmable switches offer the flexibility to be set for Push to Talk, Push to Mute or Push On/Push Off modes. Attractively designed with a low profile, professional appearance, the Microflex Boundary microphones come with an easy to use paint mask for your custom-color installations. Find out why we call the new Microflex Boundary microphones "the smart choice" for just about every application. Take a listen today.
Model | Description | MX391/C - Cardioid | Miniature Black Condenser Boundary Microphone, In-Line Preamp, 12 foot (4 meter) Attached Cable to 4-Pin Mini Connector | MX391/S - Supercardioid | MX391/O - Omnidirectional | MX391/C - Cardioid | Miniature Black Condenser Boundary Microphone, 12 foot (4 meter) Attached Cable to 4-Pin Mini Connector, MX1BP Preamplifier | MX391/S - Supercardioid | MX391/O - Omnidirectional | MX391LP/C - Cardioid | Miniature Black Condenser Boundary Microphone (Wireless Compatible), 12 foot (4 meter) Attached Cable to 4-Pin Mini Connector Less Preamplifier | MX391LP/S - Supercardioid | MX391LP/O - Omnidirectional | MX391WLP/C - Cardioid | Miniature White Condenser (Wireless Compatible) Boundary Microphone, 12 foot Attached Cable to 4-Pin Mini Connector, Less Preamplifier | MX391WLP/S - Supercardioid | MX391WLP/O - Omnidirectional | MX391W/C - Cardioid | Miniature White Condenser Boundary Microphone, 12 foot (4 meter) Attached Cable to 4-Pin Mini Connector, In-Line Preamplifier | MX391W/S - Supercardioid | MX391W/O - Omnidirectional | MX392/C - Cardioid | Condenser Boundary Microphone, Built-in Preamp, Attached 12 foot (4 meter) Unterminated Cable, Logic Functions, Programmable Switch and LED Indicator | MX392/S - Supercardioid | MX392/O - Omnidirectional | MX393/C - Cardioid | Condenser Boundary Microphone, Built-in Preamp, 12 foot (4 meter) 3-Pin Mini Connector (TA3F) to male XLR, Programmable Switch and LED Indicator |
|
Reviews
There are no reviews yet.