Content |
Specifications
General
Recording media CompactFlash card
Tested media SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system FAT32
File format BWF (single-channel, multi-channel)
Number of audio channels 8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates 16 bit/24 bit
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates 23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic Omni directional, monaural
Low cut filter Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8) XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance (LINE) 10 kOhm
Nominal input level (LINE) + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
Maximum input level (LINE) Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
Input impedance (MIC –25) 2.4 kOhm
Minimum input level (MIC –25) –45 dBu
Maximum iput level (MIC –25) +11 dBu
Input impedance (MIC 0) 2.4 kOhm
Minimum input level (MIC 0) –70 dBu
Maximum input level (MIC 0) –14 dBu
LINE OUT connectors (L/R) XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance 100 Ohm or less
Nominal output level +6 dBu (Ref. level: –9 dB)
Nominal output level +4 dBu (Ref. level: Other than –9 dB)
Maximum output level Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector 6.3-mm stereo phone jack
Maximum output power 100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector D-Sub, 25-pin connector
Format AES3-2003/IEC60958-4 (AES/EBU)
Minimum input voltage 200 mVpp
Maximum input voltage 7 Vpp
Output voltage 3.5 Vpp
DIGITAL OUT connectors BNC
Format AES3-2003/AES-3id-2001 (AES/EBU)
Output voltage 1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
Input voltage 11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector BNC
Input voltage 5 V TTL equivalent
Input impedance 75 Ohm ±10 %
Allowable frequency deviation of external sync ±100 ppm
CASCADE/WORD OUT connector BNC
Output voltage 5 V TTL equivalent
Output impedance 75 Ohm ±10 %
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector BNC
Input voltage 0.5–5 Vpp
Input impedance 10 kOhm
TIME CODE OUT connector BNC
Output voltage 2.0 Vpp
Output impedance 600 Ohm
USB port USB B-type, 4-pin
Format USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)
All sample rates 20 Hz – 20 kHz, 0 dB (±0.5 dB)
88.2/96 kHz sample rates at 40 kHz –1 dB (±1.0 dB)
176.4/192 kHz sample rates at 80 kHz –3 dB (+1/–2 dB)
Distortion
LINE IN to LINE OUT 0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
MIC IN (MIC –25) to LINE OUT 0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
MIC IN (MIC 0) to LINE OUT 0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio
LINE IN to LINE OUT 110 dB(A) or more (22 kHz LPF)
MIC IN (MIC –25 or MIC 0) to LINE OUT 100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows Windows XP, Windows Vista, Windows 7
CPU Pentium 300 MHz or faster
Memory 128 MB or more
USB USB 2.0 port
Macintosh Macintosh Mac OS X 10.2 or later
CPU Power PC G3, G4, Intel Mac 266 MHz or faster
Memory 64 MB or more
USB USB 2.0 port
Recommended USB host controller Intel chipset
Power supply and other specifications
Power requirements 100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation) Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
NP type battery (Li-Ion: 14.8 V/4.6 Ah) About 5 hours
AA type batteries (NiMH) About 2 hours
Power consumption 18 W
Dimensions (W x H x D) 270 mm x 100 mm x 260 mm (excluding protrusions)
Weight 3.65 kg (excluding batteries)
Operating temperature range 0–40 ºC
|
Liquid Mix HDLiquid Mix HD | TDM Plugin for Pro Tools HD
Key Features
Variety of Classic Emulations
40 compressors and 20 EQs, sampled from vintage originals with a free expanding library online.
Dynamic Convolution Technology
The unique patented Dynamic Convolution process delivers unparalleled EQ and Compression emulations.
Ultra-Low Latency for Recording
With the ultra-low latency of Liquid Mix HD (just 12 samples), it can now be used for recording and live sound applications
Optimised for Pro Tools HD
Over one hundred simultaneous mono instances can be run at 44.1/48kHz on an HD3 system.
Full Control Surface Mapping
Pro Tools TDM format ensures full control mapping on all major Pro Tools control surfaces, including ICON and VENUE.
Unique Hybrid Super EQ
Create your own totally unique 7-band super EQ, built out of separate classic EQ bands.
Compressor 'Free' Mode
Vintage compressors with limited controls can now be set to provide fully variable Attack, Release and Ratio.
Automation and Full Recall
Perfect integration with Pro Tools HD allows for automation of parameters and full recall within your session.
|
The HD-R1 Solid State Recorder is a two-channel, single rack-mount recording and playback device created with the sound contractor in mind.
Utilizing the highly reliable Compact Flash Card the HD-R1 records 44.1 to 96kHz, 16/24 bit PCM or MP3 files. The ability to control the HD-R1 remotely is provided via RS-232, Parallel, and RJ45 100Mbit Ethernet. File transfer can be accomplished via Ethernet and/or USB (type "A" connector).
To further enhance the HD-R1's feature set, Mic preamps (w/20dB pad) and Phantom Power (rear-panel selectable) have been included. The HD-R1 offers a variety of contractor-friendly I/O options; such as, Unbalanced (RCA), Balanced (XLR and Euroblock), and S/PDIF Digital (Coaxial and Optical).
And of course... the traditional source device features are Power-on-Play, Front Panel Rotary Input Level Controls, Headphone Jack with level control, and a variety of Playback Modes.
* 1U Rack-mount Solid-State Recorder
* Compact Flash Card
* USB host interface for USB Flash Cards
* Audio data formats: PCM (16/24 bit), MP3
* Sampling rates supported: 44.1, 48, 88.2, 96kHz
* Mic/Line XLR (with 20dB pad) balanced I/O
* Phantom Power (rear panel switch and front LED indicator)
* Euroblock terminal (Input and Output)
* Unbalanced RCA (Input and Output)
* Front panel rotary input level controls
* RS-232 interface for control
* RJ45 100Mbit/s Ethernet interface for file transfer and control
* 25-pin parallel remote control interface
* 16 Direct Play via D=SUb25 pin parallel interface
* Power on play (front panel selectable)
* S/PDIF Digital In/Out (Coaxial and Optical)
* Headphone Jack w/level control
* Input through and Auto Fade function
* Input monitoring / mixing of live stereo input along with playback
* Program Play, Folder Play, Shuffle Play, Interval Play modes, etc...
|
UR-80: 24 Bit/96 kHz USB Recording System
Features
- Over forty assignable controls
- Up to 24-bit/96KHz recording
- 2x XLR/TRS combo jack with qualified microphone preamp & phantom power
- Included HQ-GM2, HyperCanvas software synthesizer
- ASIO2.0/WDM, MacOS X compatible drivers, low-latency support.
- UR-80 Editor Software Included
- V-Link support
Knob8Fader9Rotary Encoder1Button25LED10Number of Memory SetsPreset1User7Number of Audio Record/Playback Channels (Full duplex (except for 96 kHz setting))Record2 channels (stereo)Playback2 channels (stereo)Signal ProcessingAD/DA Conversion24 bits (linear)PC interface24 bitsSampling Frequency24 bitsDigital output44.1/48/96 kHzDigital input32/44.1/48/96 kHz* Built-in realtime sample rate converterAD/DA Conversion44.1/48/96 kHzFrequency Response96.0 kHz20 Hz to 40 kHz (+0 dB/-2 dB)48.0 kHz20 Hz to 22 kHz (+0 dB/-2 dB)44.1 kHz20 Hz to 20 kHz (+0 dB/-2 dB)Nominal Input Level (variable)Input Jack 1, 2 (XLR type)-50 to -10 dBuInput Jack 1, 2 (1/4 inch TRS phone type)-35 to +4 dBuInput ImpedanceInput Jack 1, 2 (XLR type)5 k ohmsInput Jack 1, 2 (1/4 inch TRS phone type, Lo-Z)32 k ohmsInput Jack 2 (Hi-Z)1 M ohmsNominal Output LevelOutput Jack0 dBuOutput ImpedanceOutput Jack1 k ohmsHeadphones160 ohmsResidual Noise LevelOutput Jack-90 dBu or less
(input terminated with 1 k ohms, OUTPUT VOLUME: max., INPUT SENS = min., INPUT MONITOR = min., IHF-A, typ.)InterfaceUSB
Digital input/output Coaxial type
Optical type(conforms to S/P DIF)ConnectorsInput Jack 1, 2 (XLR type (phantom power)
1/4 inch TRS phone type)
Digital In Connectors (Coaxial type, Optical type)
Digital Out Connectors (Coaxial type, Optical type)
Headphones Jack (Stereo 1/4 inch phone type)
Output Jack L/R (RCA phone type)OthersPower SupplyAC adaptorCurrent Draw1000 mAAccessoriesInstallation Guide
Owner's Manual
USB cable
AC adaptor
CD-ROM
Overlay Sheets with Application LabelsSize and WeightWidth379 mm14-15/16 inchesDepth239 mm9-7/16 inchesHeight84 mm3-5/16 inchesWeight1.7 kg3 lbs. 11 oz.
|
Features at a glance - Supports Sennheiser wireless system mics and transmitters (DR-10CS)
- Supports Shure wireless system mics and transmitters (DR-10CH, DR-10CS with optional AK-DR10CH panel)
- Supports Sony/RAMSA wireless system mics and transmitters (DR-10CS/DR-10CH with optional AK-DR10CR panel)
Note: The Sony/RAMSA panel has a sliding switch to allow proper wiring configuration - 48kHz/24-bit linear PCM mono recording
- WAV files (compatible with BWF format)
- Media: microSD/SDHC cards (supports 32GB capacities)
- Sliding record switch and hold function to prevent misoperation during recording
- Dual recording function
- automatic file closing function to prevent the loss of already recorded data
- High/Mid/Low recording level settings
- Low-cut filter
- Limiter
- Automatic level function
- With a built-in clock function, supports BWF files that can have time information added - convenient for editing and searching
- Time track incrementing function can create new files at regular intervals (every 15 minutes) during recording
- Playback function allows recorded data to be checked immediately
- Headphone output
- Easy-to-read organic EL display
- micro USB B port enables easy data exchange with computers
- Records at least 10 hours on a single AAA battery * using alkaline batteries (EVOLTA)
- Unit settings can be created and transferred as a computer text file
- Settings can be transferred between DR-10C units using the infrared transmission function
- Firmware can be updated using a microSD card
- Belt clip included
- Silicon band that can be used to attach the unit to a transmitter included
- Custom case for storing the unit and accessories included
- RoHS-compliant product
|
The APH-2n optional accessory pack includes seven tools for use with the H2n. The remote control can be used to start, stop and pause recordings as well as to add marks. The other accessories in the pack are a windscreen that reduces wind and breath noise, a mic clip adapter for use with a mic stand, a tabletop tripod with extendable legs, a padded-shell case, an AC adapter and a USB cable. |
Reviews
There are no reviews yet.