| Content |
The VX-200SZ is an audio signal output module of the VX-2000 system with speaker line impedance detection. This module is to be mounted in the VX-2000SF Surveillance Frame and detects speaker line short circuits, open circuits by comparing impedance readings, and ground fault.
| Power Source | Supplied from VX-2000SF | | Current Consumption | Under 150 mA | | Power Amplifier Link | RJ45 female connector for connecting the VP-2064, VP-2122, VP-2241,
VP-2421 Power Amplifier.
Twisted-pair straight cable (TIA/EIA-568A standard) | | External Attenuator Control Output | Plug-in screw connector, relay, no-voltage make contact output,
transfer type, withstand voltage: 30 V DC, 250 V AC,
contact current: Under 7 A (DC), under 7 A (AC)
Applicable cable diameter: AWG 24 - AWG 16 | | Speaker Output | Plug-in screw connector
Applicable cable diameter: AWG 24 - AWG 16 | | Power Amplifier Input | Plug-in screw connector for connecting the VP-2064, VP-2122, VP-2241,
VP-2421 Power Amplifier.
Applicable cable diameter: AWG 24 - AWG 16 | | Fault Detection System | Short circuit, open circuit (impedance detection method), ground fault | | Finish | Panel: Surface-treated steel plate | | Dimensions | 30.5 (W) × 132.6 (H) × 290.3 (D) mm | | Weight | 320 g | | Accessory | Plug-in screw terminal……1 | | Option | Equaliser card: VX-200SE | | Applicable Model | VX-2000SF |
| RM-200M - Five/ten zone console for VM-2120/2240 amplfiers
The RM-200M Remote Microphone that allows announcements to be made to any speaker zone and emergency announcements to all zones on a system with the VM-2120/2240 system management amplifiers.
These announcements can be made live or pre-recorded announcements
can be activated. The remote microphone is connected by cable to the
RM-210 Remote Microphone Extension unit.
SPECIFICATIONS:
| Power Requirement |
24 V DC (12-30 V DC), (Supplied from VM-2120/VM-2240 Amplifier or local power suppy.) |
| Distortion |
Less than 1% |
| Frequency Response |
100 - 10,000 Hz |
| Distortion |
Less than 1% |
| Signal-to-Noise Ratio |
More than 60 dB |
| Audio Output |
0 dB*1, 600 O, balanced |
| Microphone |
Unidirectional electret condenser microphone, gooseneck type. |
| Speaker Zone Control |
Zones 1-5 (Zones 1-10 with 2 stacked amplifiers) Groups 1-2, and All-Zone Broadcast |
| Emergency Broadcast |
Activation of Emergency Broadcast (pre-recorded announcement*2 or live microphone announcement) by Emergency Switch |
| Voice Announcement Board Control |
Activation of 5 messages*2 |
| Number of Connectable Units |
Up to 4 |
| Communication System |
RS-485 |
| Volume Control |
Microphone volume control |
| Connection Cable and Connector Category |
5 STP cable, RJ45 connector |
| Communication Distance |
800 m maximum in total |
| Finish |
ABS resin |
| Dimensions |
190 (W) × 75.7 (H) × 21.5 (D) mm (Gooseneck microphone excluded) |
|
*1 0 dB = 1 V
*2 An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier. |
|
| - CONSIDERATION OF USERʼS CONVENIENCE NUMERIC buttons and various function buttons are separated for timer program enter and convenience in use so that the user can easily operate. - ADOPTION OF VACUUM FLUORESCENT DISPLAY PANEL Adopting a vacuum fluorescent display of a dot matrix method enables to check operation status of each function at a glimpse. - PROGRAMMING USING A PC You can easily execute reservation setting thorough management program by connecting a PC to the RS-232C port. - VARIOUS MELODY AND SOUND OUTPUT You can generate various melodies and sounds by linking the flash memory mounted on this unit to our model, PV-632 (MULTI-VOICE FILE). - AC POWER OUTPUT CONTROL When PW-642 and other equipment are connected via the AC outlet terminal of PW-642, you can turn ON/OFF the AC outlet button in the front panel and manually control ON/OFF of the AC power connected to other device. - BACK-UP POWER You can continue to maintain the time counter for about a week though the inner back-up even though AC power turns off with current time set. There is no need of readjusting time even though AC power is applied. - MEASURE AGAINST POWER FAILURE A separate memory is used to prevent data extinguishment due to power failure or other unstable power. - AUTOMATIC RETURN In programming data using a key button on the front side of PW-642 without using a PC, no pressing any button is recognized as cancel of program entry to return to normal operation status. - AC POWER OUTPUT TIME ADJUSTMENT You can adjust the AC power output time of PW-642 by 1~20sec to prevent time delay from occurring in the interface with the outside power amp. - KEY LOCK You can protect reservations and userʼs setting. |
|
|
| | | PW - 642 | | Input Channel (Balanced) | 5CH | | Output Channel (Balanced) | 4CH | | Output Level | Maximum 1v | | AC Power Output 1 | Maximum 500W | | AC Power Output 2 | Maximum 30 w | | Data Preservation Time | 7 days and more | | Melody Time (15 settings total - 247 seconds) | No.1 | 2 seconds | | No.2 | 3 Seconds | | No.3 | 3 Seconds | | No.4 | 5 Seconds | | No.5 | 5 Seconds | | No.6 | 7 Seconds | | No.7 | 7 Seconds | | No.8 | 10 Seconds | | No.9 | 10 Seconds | | No.10 | 15 Seconds | | No.11 | 20 Seconds | | No.12 | 30 Seconds | | No.13 | 30 Seconds | | No.14 | 40 Seconds | | No15 | 60 Seconds | | Operation Temperature | -10°C ~+ 40°C | | Power Source | 100- 120 VAC or 220 -240VAC; 50/60 Hz (Supplied AC mains transformer depends on country requirements) | | Power Consumption | 10W | | Weight(SET) | 5.7Kg/12.6Ib | | Dimension(SET) | 482(W) x 88(H) x 380(D)mm/19(W) x 3.5(H) x 15(D)in | | ※ Specifications and design subject to change without notice. | | | |
|
| | - SYSTEM POWER CONTROL It controls the power of the rack system over all working together with the PD-659. - AC OUTLET TERMINAL To make the units using AC work, it has an AC outlet terminal for your convenience. AC switched group turn on and off repeatedly every 2 seconds. | | | | | | | PD- 658 | | AC Outlet | Switched 2000W ⅹ3 | | Operation Temperature | -10℃~+40℃ | | Power Source | 100-120VAC or 220-240VAC; 50/60Hz (Supplied AC mains transformer depends on country requirements) | | Power Consumption | 10W | | Weight(SET) | 4.6Kg/10.1 Ib | | Dimension(SET) | 482(W) x 88(H) x 380(D)mm/19(W) x 3.5(H) x 15(D)in | | | |
|
The RM-300MF Fireman's Microphone is designed for exclusive use with the VM-3000 Series. It is equipped with an emergency activation key, permitting pre-recorded evacuation and alert announcements to be activated, and microphone announcement to be made in emergency situations. By connecting the RM-320F Fireman's Microphone Extension to the RM-300MF, the number of function keys can be expanded. The zone selection or failure acknowledgment function can be assigned to such function keys.
|
Power Source
|
24 V DC (operating range: 15 - 40 V DC, supplied from the VM-3000 system)
| |
Current Consumption
|
120 mA (RM-300MF), 660 mA (with 3 RM-320F connected)
| |
Frequency Response
|
200 Hz - 15 kHz
| |
Distortion
|
1 % or less
| |
S/N Ratio
|
55 dB or more
| |
Microphone
|
Unidirectional dynamic microphone with talk key, compressor (on/off switchable)
| |
Volume Control
|
Microphone volume control, Buzzer volume control
| |
Connection Cable
|
Main line: Shield CPEV cable (each one pair of Audio line, Data line, Power supply line)
or Category 5 Shielded Twisted-Pair straight cable for LAN (CAT5-STP), M3 screw terminal
| |
Maximum Cable Distance
|
Total 800 m (874.89 yd)
| |
No. of Connectable RM-320F
|
Max. 3 units
| |
Operation
|
Emergency key, Evacuate key, Alert key, Emergency reset key, CPU switch, Reset switch
| |
Indicator
|
Power indicator, Emergency indicator, Communication failure indicator, CPU OFF indicator,
Evacuation announcement indicator, Alert announcement indicator,
Emergency reset indicator, Microphone in-use indicator,
Emergency broadcast equipment in-use indicator
| |
Operating Temperature
|
-5 ℃ to +45 ℃ (23 ゜F to 113 ゜F)
| |
Operating Humidity
|
5 % to 95 %RH (no condensation)
| |
Finish
|
ABS resin, blueish gray (PANTONE 538 or its equivalent)
| |
Dimensions
|
200 (W) × 215 (H) × 82.5 (D) mm (7.87" × 8.46" × 3.25“)
| |
Weight
|
1.1 kg (2.43 lb) (with wall mounting bracket unit)
| |
Accessory
|
Wall mounting bracket unit…1, Wall mounting screw…2
|
|
Five attenuation settings (OFF, 0/-6/-12/ -16dB), over an input range from 0.5W to 30W. |
Reviews
There are no reviews yet.