| Content | The MINIFBQ FBQ800 features Behringer's FBQ Feedback Detection System that instantly reveals critical frequencies and can also be used as an audio analyzer. An additional low cut filter removes unwanted frequencies such as floor rumble. Accurate 6-digit LED input/output meters and level control are provided for precise level indication. Long-term reliability is guaranteed with Behringer's high-quality illuminated faders, potentiometer and illuminated switches. The ultralow noise audio operational amplifiers offer outstanding sound performance. In addition, all Mini Series models can be stacked on top of each other to create an ultra-compact signal processing solution.
How Does it Work?
Imagine the frequency range of the sound you hear as a highway, a very wide one with nine lanes. Each of these "lanes” represents a single octave of the sonic spectrum. The first four lanes, labeled 63 - 500 (Hz) contain the really low frequency sound content, mainly bass, bass vocals, and the kick and tom drums. The three lanes labeled 1k, 2k and 4k (Hz), make up the fundamental zone of most musical instruments and the male and female vocals. 8k and 16k cover the frequency range of cymbals, snare drums and higher pitched percussion instruments. The FBQ800 allows you to control the flow of audio traffic in each of these nine lanes. When properly applied, EQ makes it possible to hear all of these frequency ranges equally, thus the term equalization.
Feedback Elimination
When a specific frequency, or range of frequencies, reaches too high a level, feedback occurs—that all-too-familiar squeal or howl you get when the mic is too close to the speaker. Basically, feedback happens when there is so much of a particular frequency that it is picked up by the mic and run through the system again. Thatʼs why feedback typically gets louder and louder the longer itʼs allowed to occur. Needless to say, this kind of feedback is very undesirable.
This is where the FBQ800ʼs Feedback Detection System really works its magic. In this ingenious circuitry, LEDs on the individual faders light up when that frequency band is approaching the danger zone. All you need do is lower the illuminated slider until the LED blinks out—voilà, feedback problem solved! What once required a highly trained ear is now an activity that even a child can master.
Sonic Toolkit…
That really is the best way to describe the FBQ800. With its nine frequency bands, you easily fine-tune your sound and instantly eliminate feedback. And each fader can be used to boost or cut the frequency range it controls by as much as 12 dB (and thatʼs a lot!).
Special attention is paid to the low frequency zone. In addition to low frequency faders, the FBQ800 features a Low Cut filter for removing unwanted low frequencies such as floor rumble, room resonance, electrical hum, etc. This is especially handy if your system is being used for speech rather than music.
To Boost or to Cut, That is the Question
Raising and lowering specific frequency bands can improve the frequency response of any roomʼs acoustics. For instance, if the room youʼre in is "bass-heavy,” lowering the 63 and 125Hz faders can help eliminate an overall "boomy” or "muddy” sound. Likewise, gently boosting the 8 and 16k sliders can add sparkle to a somewhat "dark” mix. Are the vocals getting lost in the mix? Raising the level of the 1k slider can help bring them out.
Itʼs important to note that raising a single fader level is not always the best solution; itʼs often better to lower the bands surrounding the frequency you want to bring out, and then boost the overall volume level to achieve better headroom.
Built for Accuracy and Reliability
Speaking of headroom, FBQ800ʼs 6-digit LED I/O meters and level control are provided for precise level maintenance. Long-term reliability is ensured, thanks to high-quality illuminated faders and switches, and our ultra low-noise audio operational amplifiers provide outstanding sonic performance. In addition, all Mini Series components can be stacked to create an ultra-compact signal processing solution.
Mini Series mixer with built-in feedback detection.
FEATURES
- Ultra-compact 9.5" graphic equalizer for studio and stage applications
- FBQ Feedback Detection system instantly reveals critical frequencies
- Additional Low-cut filter removes unwanted frequencies, like floor rumble
- 6-segment LED input/output meters and Level control for precise level indication
- High-quality illuminated faders, potentiometers and illuminated switches
- Low noise audio operational amplifiers offer excellent sound performance
SPECIFICATIONS
MINIFBQ FBQ800 9-Band Graphic Equalizer with FBQ
- INPUT
- Type 1/4" TRS connectors (balanced) or
- RCA connectors (unbalanced)
- Impedance approx. 20k ohms, balanced
- approx. 10k ohms, unbalanced
- CMRR 40 dB typ. @ 1 kHz
- Max. input level +15 dBu
- OUTPUT
- Type 1/4" TS connectors (unbalanced) or
- RCA connectors (unbalanced)
- Impedance approx. 120 ohms
- Max. output level +15 dBu
- SYSTEM SPECIFICATIONS
- Frequency response 10 Hz to 200 kHz, -3 dB
- Dynamic range 110 dB, 10 Hz to 22 kHz
- Distortion 0.003 % typ. @ 0 dBu
- Crosstalk
- Signal-to-noise ratio 10 Hz - 22 kHz
- GRAPHIC EQUALIZER
- Type 9 analog stereo bands
- Control range ±6 dB or ±12 dB, switchable
- Bandwidth 1 oct.
- OTHER FEATURES
- Low-cut filter 75 Hz (12 dB/oct.)
- Input level control -12 dB to +12 dB
- POWER SUPPLY
- Mains connection external power supply
- 9 V ~ / 750 mA
- Mains voltage
- DIMENSIONS/WEIGHT
- Dimensions (H x W x D) approx. 1 8/9" (48 mm) x 9 5/9" (243 mm) x 4 5/7" (120 mm)
- Weight approx. 0.86 lbs. ( 0.39 kg)
|
* 2 channel 15 2/3 octave band graphic equalizer
* 25Hz - 16kHz frequency control * Constant Q circuitry
(3% frequency accuracy) * Selectable 6dB or 12dB control
* Variable level control * By-pass switch * Overload threshold LED (5dB below clipping) * Ground lift switch * XLR & 1/4" TRS balanced Inputs/Outputs * Power: Selectable 120V/220V voltage
* Dimensions: 1.75" H x 19" W x x 8.5" D / 44.5mm x 483mm x 216mm - 1 space r.m. * Weight: 4.5 lbs. / 2.5kg
XEQ-152 Specifactions:
* Input type: Active balanced / Unbalanced * Output Impedance: | INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typicall >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
|
DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction
It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.
But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!
SPECIFICATIONS:
|
INPUT
| |
Connectors:
|
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Electronically balanced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 40k ohm, unbalanced 20k ohm
| |
Max Input Level:
|
>+21dBu balanced or unbalanced
| |
CMRR:
|
>40dB, typically >55dB at 1kHz
| |
OUTPUTS
| |
Connectors:
|
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Impedance-balanaced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 200 ohm, unbalanced 100 ohm
| |
Max Output Level:
|
>+21dBu balanced/unbalanced into 2k or greater
>+18dBm balanced/unbalanced (into 600)
| |
SYSTEM PERFORMANCE
| |
Bandwidth:
|
20Hz to 20kHz, +/-0.5dB
| |
Frequency Response:
|
50kHz, +0.5/-3dB
| |
Noise Reduction In:
|
(+/-6 and +/-15dB range):
| |
Signal-to-Noise:
|
>102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>120dB, unweighted
| |
Noise Reduction Out:
|
(+/-6dB range):
| |
Signal-to-Noise:
|
>94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
| |
Dynamic Range:
|
>112dB, unweighted
| |
Noise Reduction Out:
|
(+/-15dB range):
| |
Signal-to-Noise:
|
>90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>108dB, unweighted
| |
THD + Noise:
|
| | High-Definition 31-Band Stereo Graphic Equalizer with FBQ Feedback Detection System
- Professional 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated mono subwoofer output with adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies, e.g. floor rumble, hiss etc.
- Highly accurate 12-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard-bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- 3-Year Warranty Program*
- Conceived and designed by BEHRINGER Germany
|
Reviews
There are no reviews yet.