| Content |
Get some huge tube tone from the tiny Bugera T5 INFINIUM Guitar Amplifier Head. With this head weighing in at under 10 pounds, you can take it from silent headphone practicing in your apartment to the recording studio, or to your next club gig and plug it into a (separately available) cabinet. The simple single-channel design allows you to dial in your tone quickly, while the PHAT switch adds a gain boost and bypasses the EQ section for a more raw sound. Onboard reverb completes the package, adding subtle ambience or washy overtones to your sound.
Aesthetically, the T5 features a vented metal top which shows off the 12AX7 preamp and EL84 power amp tubes\' glow, along with the other amp components. An orange classic jewel status light shines when the power is on.
Classic All-Tube DesignThe T5 INFINIUM features Class-A technology with a 12AX7 front-end and an EL84 power stage. The tube design provides sweetly balanced harmonics and natural tube compression, resulting in the warm distortion and break-up you\'ve come to love from those vintage megaliths of yesteryear—in a portable and attractive chassis. The 12AX7 preamp tube can produce everything from soulful blues to mind-blowing crunch. Often employed in classic British-style amplifiers, the EL84 output tube is known for its crisp and chiming tonal quality. The built-in power attenuator can harness that power for reproducing a hard-working power amp tone at lower volume levels.INFINIUM TechnologyBy continuously monitoring the tube circuitry, INFINIUM lengthens tube life and keeps your tone consistent throughout the life of your tubes. When INFINIUM detects a change in tube operation due to aging or otherwise, it dynamically adjusts the circuitry so the tubes operate at their optimal load.
INFINIUM also knows when the power tube needs to be replaced and will illuminate an LED on the rear panel to notify you. Auto-Bias circuitry allows you to replace the tube without any esoteric or potentially dangerous adjustments that would require a trip to an amp tech.
Built-In ReverbT5\'s Reverb puts the finishing touch to your sound. Adjustable via the dedicated control on the front panel, you can dial in the level you desire—from a subtle touch to the cavernous, natural-sounding reverberation of a large arena.Power Attenuator and Speaker EmulationThe convenient, built-in Power Attenuator allows you to operate the T5 at your choice of 5 Watts, 1 Watt, or even 0.1 of a Watt, so you get everything from sweet and sassy to maximum tube saturation, even at reduced volume levels. The stereo headphone output has speaker emulation that tailors your tone for silent practicing.
| General |
|---|
| Dimensions (WxHxD) |
6.1 x 8.8 x 6.5“ / 155.0 x 223.0 x 165.0 mm Amplifier |
| Weight |
9 lb / 4.08 kg Amplifier |
| Amplifier Type |
Tube |
| Output Power |
5 W |
| Channels |
1 |
| Tube Types |
1 x Preamp 12AX7/ECC83
1 x Power EL84/6BQ5 |
| Output Impedance |
4 ohms Mono |
| Effects Loop |
No |
| Built-In Effects |
Digital Reverb |
| Master Volume |
Yes |
| Inputs |
1 x 1/4“ Mono Instrument |
| Outputs |
1 x 1/4“ Mono Speaker
1 x 1/4“ Stereo Headphone |
| Tone Section |
Bass, Gain, Treble |
|
Info
Marshall 2555X Silver Jubilee, all-valve electric guitar head, 100W, 2 channels, preamp tubes: 3x ECC83, power amp tubes: 4x EL34, 1x input, controls: input gain (push/pull: rhythm clip), lead master, output master, treble, middle, bass, presence, pentode/triode switching, FX loop, DI out, incl. footswitch (channel change), speaker outputs: 1x 16 ohms, 1x 8 ohms (or 2x 16 ohms) & 1x 4 ohms (or 2x 8 ohms), dimensions: 750 x 230 x 310mm, weight: 22,1kg
| Palmer EINS - Amazingly versatile!
Small 1-5W amps have become very popular in recent years. They are fun items but some seem more like toys than real amplifiers.Palmers approach with the EINS was to design a serious true tube amplifier for professional purposes. The speaker simulated output allows you to connect the output of the amp directly to your audio interface. Thanks to the integrated loadbox aspeaker does not need to be connected. Thanks to the unique "HiZ output” you can connect the output of the EINS directly to the input of any amplifier! This way the EINS can be power boosted or used as a preamp or even on your pedalboard.
The Palmer EINS comes with an ECC83 preamp tube (V1) and an ECC82 (V2) power stage tube as standard. Other tube configurations are possible as follows.
- 1: V1:ECC83 - V2:ECC83: Quieter, distorts much faster, a little more gain, lead sound.
- 2: V1:ECC83 - V2:ECC81: Louder than Variation "1“, quieter than the standard configuration, more gain, distorts a little more quickly.
- 3: V1:ECC81 - V2:ECC82: Stays clean a little longer, a little more headroom, darker distortion sound.
- 4: V1:ECC81 - V2:ECC83: The quietest configuration, distortion sets in a little later than with Variation "1“, distortion can be controlled very precisely.
- Type: head
- technology: Tube
- class: A
- power: 1 W
- Inputs: 1
- input connectors: 6.3 mm Jack
- Input impedance: 1 M ohm
- outputs: 4
- output connectors: 6.3 mm Jack
- output impedance: Speaker out: 8 & 16 Ohm, Simulated out: 4k, HiZ out: 3,3M ohm
- Channels: 1
- Indicators: Power
- controls: Level, Tone
- FX loop: no
- Power supply: 230 VAC
- Power consumption: 10 W
- preamp tubes: ECC83
- power amp tubes: ECC82
- rectifier: solid state
- cabinet material: sheet steel
- Cabinet / Housing surface: powder coated / anodized
- width: 206 mm
- depth: 128 mm
- height: 108 mm
|
Marshall 2245-01 30W Guitar Amplifier
When Jim Marshall first started manufacturing Marshall amps, back in 1962, the first amp out of the workshop was the JTM45. This amp instantly became a hit and launched a whole new generation of amazing guitar players. Since then, connoisseurs of tone have searched high and low for original examples of this beautiful amp. Now they need search no more, Marshall has re-issued the JTM45 complete with its full quota of glassy clean tone and fluid warm sustain.
By including GZ34 valve rectification, as found in the original, Marshall has ensured a faithful recreation of the JTM45s glorious sound. The GZ34 rectifier valve interacts with the rest of the valves causing subtle harmonics to shift and smoulder beneath every note you play.
| Model Name | JTM45 (2245) | | Series | Vintage Reissue | | Tubes | 3 ECC83 (Preamp), 2 5881 (Power Amp) | | Output | 30 Watts | | OHMS | 16 | | Speakers | n/a | | Effects | n/a | | Covering | Black Vinyl | | Footswitch | n/a | | Dimensions | 660x260x205mm | | Weight | 14.6kg |
| Building on the overwhelming success of our acclaimed Dark Terror and Dual Dark amps, weʼve distilled thousands of customer demands into a pint-sized valve hybrid head – the Micro Dark. The Micro Dark shares the same intuitive Shape control combined with a new 12AX7-driven high gain preamp section which yields screaming dirty tones that make a mockery of its miniature frame. Like its bigger brothers, however, the Micro Darkʼs smoky black chassis and simple layout actually disguises its cunning versatility.
Of course, thereʼs plenty of gain on tap to satisfy even the most discerning devotee of distortion, but this little beast is by no means just a one-trick Metal monster! Beneath the menacing exterior youʼll find a rich and diverse pallette of classy and confident tones. From squeaky clean to brash and mean – whatever your style – youʼre gonna love this thing.
Other features include a transparent fully buffered effects loop and a headphone output with our popular CabSim circuitry. With the optional PPC108 cabinet, the Micro is an ideal practice rig… Plug into something a little larger, though, and you might find your new secret weapon in the studio! |
Marshall 1987X-01 50W Guitar Amplifier
Though the 50 Watt 1987X shares the same front and rear panel features as its big brother, the 1959 SLP, it does have its own distinct personality. Sweet warm singing sounds are packed into every nook and cranny of this great tone machine. As is the case with the 1959SLP, the 1987X has fittings and hardware as true to the originals as humanly possible, thus ensuring that authentic Marshall 'Vintage' look.
Highlights
Mix the two channels together by connecting a short, screened patch lead between the second input of Channel 1 and the first input of Channel 2. If you then plug your guitar into the first input of Channel 1, you can mix the different tonal characters of each channel for greater flexibility.
The Series Effects Loop features a true bypass switch that takes the loop completely out of the circuit, thus ensuring the original tone isn't compromised. The Level Switch allows you match the loop to either stompboxes or rack units.
- Output: 50 Watts
- Pre-amp Tubes: 3 x ECC83
- Power Amp Tubes: 2 x EL34
- EQ: 3-Band
- Presence Control
|
Reviews
There are no reviews yet.