Content |
DYNACORD΄s SUB 112 is a vented, direct radiating cabinet, equipped with the high-power DYNACORD DND12S400 neodymium transducer. The conical vent system shows significantly less distortion and lower air noise at low frequencies than common circular vent openings.
The SUB 112 contains a passive filter, 6 dB/oct., that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs D 8 can therefore be directly connected in parallel to the SUB 112 if an extended bass reproduction is required. You just have to connect the SUB 112 and the D 8 with a regular Speakon cable in parallel.
The SUB 112 cabinet is made of 15mm birch plywood. All corner joints and braces are grooved and glued. The cabinet΄s surface is painted with a 2-K laquer finish . The acoustic foam front on a powder coated steel grille protects the DND12S400 woofer against damage during transport and bad environmental conditions. The connector panel uses two 4-pole Speakon connectors (INPUT/THRU) for a safe connection and easy daisy-chaining to other cabinets. The pin assignment is 1+/1-. Pins 2+ and 2- are also connected between the two Speakon connectors. A pole-mount flange allows easy speaker-on-a-stick applications. Please always take care that every speaker stack has been mechanically secured against accidental falling down. Please always consult a certified structural engineer for correct and safe setup methods.
The cabinet is equipped with four large rubber feet. Two handles allow easy and safe transport. A protective cover is available as an optional accessory.
|
The black Electro-Voice EVID-S12.1 is a 12” subwoofer designed to provide low-end reinforcement for system designers, installers, and audio engineers configuring systems for background and foreground music in stores, clubs, eateries, schools, and more. Its acoustic ports and 12” dual voice-coil, high-excursion woofer yield a frequency response of 40 to 140 Hz and a 127 dB maximum SPL.
Inputs and outputs utilize spring-loaded speaker terminals. The subwoofer can accept a stereo input and drive up to four satellite speakers (available separately). It includes hardware for mounting to a wall or corner and has an eyebolt for the attachment of a safety line.
12" dual voice-coil, high-excursion woofer and acoustic ports yield a frequency response of 40 to 140 Hz800W peak (200W continuous) power handling for 127 dB maximum SPL (133 dB peak)Spring-loaded speaker terminals for inputs and outputsSimultaneously drive up to four satellite speakers (available separately)Logo can be replaced to match speaker orientationIncludes hardware for mounting subwoofer to a wall or corner
LF Driver |
1 x 12" / 305 mm |
Input |
Spring-loaded speaker terminals |
Output |
Spring-loaded speaker terminals |
Frequency Response |
40 to 140 Hz (-10 dB) |
Sensitivity |
104 dB (eighth space on corner averaged 60 to 100 Hz, 1 W) |
Maximum SPL |
127 dB calculated, 133 dB peak |
Power Handling |
800 W peak (200 W with continuous pink noise for 100 hours) |
Low Impedance |
Yes |
Nominal Impedance |
8 Ohms |
Dimensions (H x W x D) |
16.3 x 23.0 x 11.9" / 413 x 584 x 303 mm |
Weight |
39.2 lb / 17.8 kg |
|
The TX1181 is the perfect companion sub to the TX1122 and TX1152 for compact and portable performance. Using the proven EVS18S woofer, the TX1181 effortlessly provides the low-frequency energy needed to keep up with Tour X boxes, as well as many other EV loudspeaker products. The integrated, low-pass input filter allows for single amp drive, and the high-sensitivity and excellent power handling don\'t require a large, expensive amplifier to generate high SPL. The TX1181\'s unique Backbone grille not only looks great, but also provides greater strength and damage resistance than simple grille block designs. Proprietary, ergonomically correct handles and angled input panels, and integrated, screw-in-style pole-mount make the TX1181 easy to transport and employ in a variety of applications.
Specifications
Frequency Response (-3dB) |
50 - 160 Hz |
Frequency Response (-10dB) |
45 - 700 Hz |
Recommended High-Pass Frequency |
30 Hz |
Sensitivity 1W/1m |
100 dB |
Max. SPL / 1m (calc) |
132 dB |
System Power Handling (continuous/program/peak) |
500/1000/2000 Watts |
LF Transducer |
EVS18S |
Nominal Impedance (Passive) |
8 Ohms |
Minimum Impedance |
7.5 Ohms |
Enclosure Material |
Plywood and MDF with EVCOAT |
Color |
Black |
Flying |
No |
Input Connections |
Parallel Neutrik® NL4 |
Internal Crossover |
Yes |
Speaker Type |
Subs |
Weight Net |
33.8 kg ( 74.52 lbs ) |
Dimensions (HxWxD) |
769 x 439 x 591 mm (30.28" x 17.28" x 23.27“) |
|
FB-120W
Power Handling Capacity: Continuous pink noise ? 200W, continuous program ? 600W
Impedance: 8Ω
Sensitivity: 90dB (1W/m) free sound field, 96dB (1W/m) 1/2 free sound field
Frequency Response: 40Hz-1.2kHz (+/-10dB)
Dimensions: 16“?16“?17.75" (W?H?D)
Weight: 15kg |
The SW10 STUDIO subwoofer has been designed specifically for optimum matching with the MSP series powered monitor speakers. Combined with MSP7 STUDIO or MSP5 STUDIO speakers in a stereo of surround system it can provide a seamlessly extended low end for accurate ultra wide range monitoring. A comprehensive selection of inputs and outputs as well as a phase switch and continuous high-cut and level controls make it easy to achieve optimum performance in any room and system. Whether you're simply mixing basic stereo programs or authoring DVD audio in full surround, MSP STUDIO series speakers plus an SW10 STUDIO will give you the ultimate monitoring experience.
GENERAL Type Powered Subwoofer
Crossover Frequency -
Overall Frequency Response 25Hz - 150Hz (-10dB)
Maximum Output Level 111dB, 1 m on Axis
Dimensions (W x H x D) 328 x 459 x 476 mm
Weight 26.5 kg
Magnetic Shielding Yes (Non-covered type)
SPEAKER SECTION Components LF 10" cone
HF -
Enclosure Type Bass-Reflex
Material MDF
AMPLIFIER SECTION Output Power * LF 180W
f = 100Hz, THD = 1%, RL = 8O
HF -
S/N, IHF-A filter > 100dB, LEVEL = Max
Input Sensitivity XLR-3-31 +4 dBu, LEVEL = Center
-6 dBu, LEVEL = Max
PHONE -
Input Connectors, Impedance XLR-3-31 (balanced), 10 kO
Output Connectors XLR-3-32 x 3 (balanced),
parallel connection with Input
Controls LEVEL control Center Click VR
(Min = -8 Attenuation)
LOW CUT switch -
HIGH TRIM -
LOW TRIM -
POWER SWITCH on/off
PHASE SWITCH Normal/Reverse
LPF control 40-120 Hz, 80 Hz at Center Click
Indicators LED Green: Power On
Red: Clipping
Power Consumption 160W
* These specifications apply to rated power supplies of 100, 120, 230 and 240 V.
* Specifications and appearance subject to change without notice.
|
The S8018 II high-efficiency subwoofer is the ideal low-frequency extension to complement RCF installed systems.
The low-frequency transducer is a hypervented vented, high excursion RCF Precision 18” woofer with a 4” inside/outside voice coil to minimize power compression and extend the life of the product. Using bass-reflex loading the subwoofer design ensures an efficient acoustic response down to 30 Hz. The Baltic birch plywood enclosure is painted with black, heavy duty, textured epoxy. The front is protected by a strong powder coated metal grille. The cabinet features two Neutrik Speakon™ connectors in a recessed input plate. A M20 pole mount adaptor is provided on the top of the cabinet, integrated hand carry points on the cabinet sides.
Features
- 18" high-efficiency 4" voice-coil woofer with Inside/Outside Coil Technology
- 137 dB maximum sound pressure level
- Response down to 30 Hz
- Rectangular box enclosure with protective metal grille
- 35 mm standard pole mount in top section of cabinet
- Baltic Birch cabinet painted with black, heavy duty, textured epoxy
- Integrated hand carry points
Acoustical Specifications
- Frequency Response -10 dB: 30 Hz ÷ 200 Hz
- Max SPL @ 1m: 137 dB
- System Sensitivity: 100 dB
- Nominal Impedance: 8 Ω
- Power Handling: 1500 W
- Peak Power Handling: 6000 W
- Recommended Amplifier: 3000 W
Transducers
- Woofer: 18" woofer, 4" voice coil
- Nominal Impedance: 8 Ω
- Input Power Rating: 1500 W AES
- Sensitivity: 100 dB
Input Section
- Input connector: Speakon NL4
Cabinet
- Cabinet Material: 15 mm birch plywood construction
- Handles: 2 on side
- Grille: Custom perforated steel grille
- Colour: Black, scratch resistant paint
Physical Specifications
- Height: 630 / 24.80 mm/inch
- Width: 530 / 20.87 mm/inch
- Depth: 770 / 30.31 mm/inch
- Net Weight: 43 / 94.60 kg/lbs
|
Reviews
There are no reviews yet.