TC ELECTRONIC M-3000 STUDIO REVERB PROCESSOR

Η τεχνολογία VSS3-reverb που έχει ενσωματωθεί στο Μ3000 αποτελεί πλέον μέτρο σύγκρισης στη μουσική βιομηχανία. Το Μ3000 περιλαμβάνει μερικά από τα πιο εύχρηστα, ποιοτικά και ευέλικτα reverbs για μουσική και ταινίες στην αγορά. Συνδυάζοντας τον απόλυτο έλεγχο στα early reflections με τη διαφάνεια και τις τέλειες αρμονικές στον ήχο του βάθους, η τέχνη του reverberation ανεβαίνει σε νέα επίπεδα.
Με διπλή μηχανή που επιτρέπει στη ταυτόχρονη χρήση 2 reverbs ή εφέ, βραβευμένο user interface, 600 factory presets και πολλαπλές εισόδους και εξόδους, το Μ3000 είναι μια από τις καλύτερες επιλογές για επαγγελματικού επιπέδου reverb.

Technical Specification  
 Digital Inputs and Outputs 
Connectors  XLR (AES/EBU)
RCA Phono (S/PDIF)
Optical (Toslink, ADAT)
Formats  AES/EBU (24 bit), S/PDIF (24 bit), EIAJ CP-340, IEC 958,
EIAJ Optical (Toslink), ADAT Lite pipe
Output Dither  HPF TPDF dither 8-24 bit
Word Clock Input  RCA Phono, 75 ohm, 0.6 to 10 Vpp
Sample Rates  44.1 kHz, 48 kHz
Processing Delay  0.2 ms @ 48 kHz
Frequency Response DIO  20 Hz to 23,9 kHz +0,01/-0,1 dB @ 48 kHz
 Analog Inputs 
Connectors  XLR balanced (pin 2 hot)
Impedance  20 kohm
Max. Input Level  +22 dBu (balanced)
Min. Input Level (for 0 dBFS)  -10 dBu
Sensitivity  @ 12 dB headroom: -22 dBu to +10 dBu
A to D Conversion  24 bit (1 bit, 128 times oversampling
A to D Delay  0.8 ms @ 48 kHz
Dynamic Range  >103 dB (Unweighted), >106 dB (A)
THD  -95 dB (0,0018 %) @ 1kHz
-6 dBFS (FS @ +16 dBu)
Frequency Response  10 Hz to 20 kHz: +0/-0.2 dB
Crosstalk  100 dB (unweighted), >104 dB(A)
THD  -86 dB (0.005%) @ 1 kHz
-6 dBFS (FS @ +16 dBu)
Frequency Response  10 Hz to 20 kHz: +0/-0.5 dB
Crosstalk 

Features
Enhance switch to restore spectral balance of compressed signal
Switchable Mode - Dual Channel or Stereo linked
Above or Below Threshold LEDs
Balanced XLR and Jack Inputs and Outputs
Intuitive, user friendly layout
Flawless performance

Innovation
The ARX COMPO? is a unique compressor/limiter designed for use in any
professional audio dynamics control application, packaged in a compact 1
RU chassis.The COMPO operates as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain controls.
A Stereo Link switch on the front panel lets both channels track as a stereo
pair in a Master/Slave configuration.
Enhance Switch
The COMPO features an 'Enhance' switch, which provides frequency restoration
to preserve the spectral balance of the audio signal, compensating for the sagging
Low and High frequency response of compressed program material.
The best way to think of it is as a 'smart' loudness control.
Wide Scale metering
There is comprehensive LED indication of all operating functions and status. Above
or Below Threshold LEDs on each channel give you instant visual confirmation of
compressor activity, as well as easy to read LED Gain Reduction meters.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. Other features include an Active/Bypass
switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
ARX Quality
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the ARX COMPO is the
ideal installation 'set and forget' compressor, and is also equally at home in Studio,
Broadcast and Sound Reinforcement environments.

Every day, ARX Audio interface products solve audio problems for thousands of people
around the world.

T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.4dB
Signal to Noise ratio -85 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 107 dB
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack

Front Panel Controls
Channel A Active/Bypassed IN/OUT switch
Threshold, Ratio and Output Gain controls
Numbered marker panel for labelling compressor assigns
5 segment LED Gain Reduction display
Above/Below Threshold status LEDs
Enhance switch and status LED
Stereo link switch and status LED
Channel B controls identical to Channel A
Rear Panel Connectors
Balanced XLR Input and Output connectors.
Balanced TRS jack Input and Output connectors.
AC input connector, with voltage switch and fuse.
 

DBX 1215
Ισοσταθμιστής 2 x 15 περιοχών με XLR IN/OUT

1215 Dual 15-Band Graphic Equalizer

The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.

The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.

•   Switchable boost/cut ranges of ±6 or ±15 dB
•   Electronically balanced/unbalanced inputs
•   Servo balanced/unbalanced inputs
•   RF filtered inputs and outputs
•  XLR, Barrier Strip, and 1/4" TRS connectors
•  -12dB/+12dB input gain range
•  18dB/octave 40Hz Bessel low-cut filter
•  Chassis/signal ground lift capability
•  Internal power supply transformer
•  Power-off hardwire relay bypass with 2-second power-up delay

Ισοσταθμιστής 2 x 15 περιοχών, με ρύθμιση threshold και noise reduction ανά κανάλι, 2/3RDS octave, 2U. 

DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction

 It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.

But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.

20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!

SPECIFICATIONS:

DBX ZONEPRO 1260

Ψηφιακός επεξεργαστής αναγγελιών 4 ζωνών. Διαθέτει 12 in/6 out. Διαθέτει agc (automatic gain leveler)
EQ, crossover, limiter, compressor, noise gate, parametric EQ, security lockout, AFS περιοριστή
μικροφωνισμών, RS 232 για έλεγχο και ρύθμιση μέσω PC, ethernet in & out. Δέχεται τα wall panel
dbx ZC. Ιδανικό για: ξενοδοχεία, εμπορικά κέντρα, καταστήματα, bar restaurants, cafe κτλ. δυνατότητα
να συνδεθεί και με άλλες ίδιες μονάδες και να επεκταθεί.

DBX-1074                                
4 ch noise gate με δυνατότητα λειτουργίας σε ρυθμιζόμενο εύρος
συχνοτήτων XLR in/out, insert points.

• Four independent channels of gating
• Independent key filtering
• Independent Threshold and Release controls
• Differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Stereo Coupling mode
• Switchable +4dBu or -10dBv operation per channel
  
  

  Input Connectors	XLR (Pin 2 and tip hot)
  Input Type	Electronically balanced/unbalanced, RF filtered
  Input Impedance	Balanced > 50 kOhm, unbalanced >25 kOhm
  Max Input	> +22 dBu balanced or unbalanced
  CMRR	40dB: Typically >55 dB at 1 kHz
  Key Input	Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm
  Output Connectors	XLR (Pin 2 hot)
  Output Type	Servo-balanced/unbalanced, RF filtered
  Output Impedance	Balanced 60 Ohm, unbalanced 30 Ohm
  Max Output	> +22 dBm balanced, > +20 dBm unbalanced
  Bandwidth	20 Hz to 20 kHz, +0/-0.5 dB
  Frequency Response	0.35 Hz to 200 kHz, +0/-3 dB
  Noise
  Dynamic Range	> 115 dB, unweighted
  THD+Noise	0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain),
  Interchannel Crosstalk
  Stereo Coupling	True RMS Power Summing
  Operating Voltage	100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
  Power Consumption	30 Watts
  Fuse	100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
  Power Connector	IEC receptacle
  Unit Weight	6.9 lbs.
  Shipping Weight	9.3 lbs.