Content | Half rack mixing amplifier, 60W @ 100 volt
The compact 9.5” MA60 mixing amplifier has an unseen intuitive user friendly interface and ground breaking logical rear panel. The unit comes with 1 mic/line input and 2 stereo line, mono summed inputs. On the rear you can find smart left-to-right 4 level priority system for audio routing, an emergency input, paging mic with chime and a 24VDC override output. The design of the MA60 is a true redefinition of the mixing amplifier that goes back to the basics. Everyone will understand how to install or operate these units in a blink of an eye |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 1000: 2x500 W/100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 33 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 200: 2x 100 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 15 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 400: 2x 200 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 17 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Reviews
There are no reviews yet.