Content |
The DPX Series was created in response to our dealers, contractors and users requesting a simple solution requiring general EQ and comp/limiting. Two products have been developed, the DPX-100 Graphic Equalizer & Compressor/Limiter and DPX-200 Parametric Equalizer & Compressor/Limiter. Using proven circuitry from our popular MQX and PQX series equalizers and combining these features with our CLX series compressor/limiters provides two tools no audio system should be without. By combining the features and benefits of two processors into one unit, the result is two powerful tools providing a simple solution to everyday audio applications. The EQ section of the DPX-100 is a 15-band, constant Q, 2/3 octave, ISO center, precision wein bridge filter design. Other EQ features are: frequency range from 25Hz to 16KHz, selectable 15dB or 6dB range, 25mm faders with 'center off' position, EQ in/out switch, signal present and clip LEDs and switchable 18dB/octave -20Hz high pass filter. Two separate inputs are available in the DPX-200; a microphone preamp with input pad and a line input. An input select switch and input level control are located on the front panel. The EQ section consists of 4 bands of filtering; two full-bandwidth parametric EQs as well as a low-shelf and high-shelf filter. Other EQ features are: in/out switching for each filter, cut and boost of 15dB, signal present and clip LEDs, and master EQ level control. The compressor/limiter section uses peak detection circuitry and has individual controls for gain, threshold, ratio, attack, release and output level. More compressor/limiter features include: in/out switch, 11-stage LED gain reduction meter, selectable 11-stage LED input/output level meter, and a detector patch point for frequency-selective limiting or ducking. Additional features of the DPX-100 and DPX-200 are: the equalizer section and compressor/limiter may be used independently or chained together in series, balanced XLR and inputs and outputs, extremely low noise and distortion, internal power supply and Ashly's five-year worry-free warranty. | Separate Mic Pre and Line Inputs | | 2 fully parametric bands | | Parametric filters tunable from 20Hz to 20KHz | | Adjustable bandwidth from 3 1/3 to 1/20 of an octave | | High and Low Shelf filters | | True reciprocal curves | | Individual band in/out bypass switching | | Balanced Inputs and Outputs | | XLR, 1/4" TRS audio connections | | Five Year Warranty |
|
* 2 channel 15 2/3 octave band graphic equalizer
* 25Hz - 16kHz frequency control * Constant Q circuitry
(3% frequency accuracy) * Selectable 6dB or 12dB control
* Variable level control * By-pass switch * Overload threshold LED (5dB below clipping) * Ground lift switch * XLR & 1/4" TRS balanced Inputs/Outputs * Power: Selectable 120V/220V voltage
* Dimensions: 1.75" H x 19" W x x 8.5" D / 44.5mm x 483mm x 216mm - 1 space r.m. * Weight: 4.5 lbs. / 2.5kg
XEQ-152 Specifactions:
* Input type: Active balanced / Unbalanced * Output Impedance: |
DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction
It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.
But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!
SPECIFICATIONS:
INPUT
|
Connectors:
|
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
|
Type:
|
Electronically balanced/unbalanced, RF filtered
|
Impedance:
|
Balanced 40k ohm, unbalanced 20k ohm
|
Max Input Level:
|
>+21dBu balanced or unbalanced
|
CMRR:
|
>40dB, typically >55dB at 1kHz
|
OUTPUTS
|
Connectors:
|
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
|
Type:
|
Impedance-balanaced/unbalanced, RF filtered
|
Impedance:
|
Balanced 200 ohm, unbalanced 100 ohm
|
Max Output Level:
|
>+21dBu balanced/unbalanced into 2k or greater
>+18dBm balanced/unbalanced (into 600)
|
SYSTEM PERFORMANCE
|
Bandwidth:
|
20Hz to 20kHz, +/-0.5dB
|
Frequency Response:
|
50kHz, +0.5/-3dB
|
Noise Reduction In:
|
(+/-6 and +/-15dB range):
|
Signal-to-Noise:
|
>102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
|
Dynamic Range:
|
>120dB, unweighted
|
Noise Reduction Out:
|
(+/-6dB range):
|
Signal-to-Noise:
|
>94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
|
Dynamic Range:
|
>112dB, unweighted
|
Noise Reduction Out:
|
(+/-15dB range):
|
Signal-to-Noise:
|
>90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
|
Dynamic Range:
|
>108dB, unweighted
|
THD + Noise:
|
| |
INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typically >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: | INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typicall >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
|
Reviews
There are no reviews yet.