| Content | Specifications: • Power output: 3,000 watts 2 ohm stereo per ch, 2,100 watts 4 ohm stereo per ch, 1,200 watts 8 ohm stereo per ch, 4,200 watts 8 ohm bridge-mono, 6,000 watts 4 ohms bridge-mono • Sensitivity (for full rated power at 4 ohms): 1.4V RMS • Frequency response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB • S/N Ratio (below rated 1 kHz power at 8 ohms): 103 dB (A weighted) • T.H.D.: 500 • Crosstalk (below rated power): 20 kHz - 1 kHz: >70 dB • Input impedance (nominal): 20k ohms balanced, 10k ohms unbalanced • Maximum input signal: +22 dBu typical • AC Line voltage and frequency configurations: 120 VAC 60 Hz • AC Line current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 15.3A; no more than 180 watts at idle • Operating temperature: 0°C to 40°C at 95% relative humidity (non-condensing) • Dimensions: 19" W x 3.5" H x 16.2" D • Net weight: 24 lbs. (13.6 kg). |
Low weight switching final power amplifier. Power 2X2500W / 4Ω, 2Χ3000W / 2Ω. 5000W bridged 8Ω. New integrated BSS OMNIDRIVE 4bit / 192kHz processor with Cirus Logic SHARC A / D and D / A Converters. Level MAX peak voltage and RMS compressing, limiting. New hi-end FIR and IIR filters, 2sec delay / channel, as well as DSP presets for various speakers. LCD display on the front. USB port on the front for loading firmware and Speakers Tunning presets. Analog inputs with XLR, digital input AES / EBU, ethernet input RJ-45 with TCP / IQ protocol. Advanced 3rd generation power supply that allows the amplifier to operate at any voltage. Cooling circuit with microprocessor control with adjustable speed depending on the temperature. Analog and digital outputs (THRU) XLR. Exits speakon 5-way binding post, ground lift switch. Made of cast aluminum, height 2U rack. Suitable for P.A applications but also permanent installations. Weight 10.5kg |
| Manufacturer |
POWERSOFT |
| Warranty |
4 Years Gurantee |
| Channels |
Four Channel |
| Resistance ohms |
8Ω / 4Ω / 2Ω |
| DSP |
Yes |
| Power (8 ohms/Watt RMS) per channel |
1600 |
| Power (4 ohms/Watt RMS) per channel |
2000 |
| Power (2 ohms/Watt RMS) per channel |
1800 |
| Weight (kg) |
7.8 |
|
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
| General |
| Output power per Channel |
| Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
| Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
| Max output voltage / current |
| Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
| Current |
|
|
45 Apeak |
| AC main power |
| Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
| Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
| Operating voltage |
|
|
90 V – 264 V |
| Power consumption / current draw |
| Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
| 1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
| THERMAL |
| Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
| Thermal dissipation* |
| Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
| 1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
| Manufacturer |
LAB GRUPPEN |
| Warranty |
10 Years Gurantee |
| Channels |
Dual Channel |
| Resistance ohms |
8Ω / 4Ω |
| Resistance ohms |
2Ω |
| DSP |
Yes |
| Power (8 ohms/Watt RMS) per channel |
600 |
| Power (4 ohms/Watt RMS) per channel |
1200 |
| Power (2 ohms/Watt RMS) per channel |
800 |
| Weight (kg) |
6.2 |
|
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 1500W
4Ω EIA 1 kHz 1% THD - 2500W
2Ω EIA 1 kHz 1% THD - 4000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 5000W
4Ω EIA 1 kHz 1% THD - 8000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 5.27V
32dB Setting - 2.67V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 39.1dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -104dB
Total Harmonic Distortion (THD) 0.1% @ 2Ω
0.03-0.06% @ 4Ω
0.01-0.03% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 18A
230V 50Hz - 11A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
Reviews
There are no reviews yet.