| Content |
ER-1193
1 channel 193 Freq. PLL Receiver 822-846 MHz
2 Frequencies available:
790 - 814 MHz (Germany)
822 - 846 MHz
• 193 selectable UHF Frequencies.
• Available for 1 transmitter
• True diversity technology permits minimum dropouts in the RF link
• PLL synthesised technology for
multi-channels.
• Compact half-rack metal housing for
space saving
• "Lock-on" mode avoids accidental modification of frequency, sensitivity and power-off.
Frequency Preparation: PLL Synthesised Control
Carrier Freq. range: 600 MHz- 960 MHz
Frequency Stability: ±0.005%
S/N Ratio: >100 dB
Display: LCD
Display Contents: Frequency, Antenna A/B, Mute display, RF/AF Lever Meter, battery fuel gauge
Controls: Power On/Off, Frequency Up/down Frequency Scan, Audio Level
Audio Output Level: -12 dB
AF Output Impedance: 600 Ohm
Squelch: Pilot Tone & Noise Mute
Operation Voltage: 12-18 VDC, 500 mA
Output Connector: XRL Balanced/ 6,3 mm Unbalanced
Dimension: 211 x 152 x 40 mm (LxWxH) | SLX4 - Wireless Receiver
The SLX4 receiver brings unprecedented ease of use to wireless with Automatic Frequency Selection and Automatic Transmitter Setup. With included rack hardware and detachable antennas, it is ready for immediate installation right out of the box.
SLX Wireless Systems feature Shure's patented Audio reference Companding for crystal-clear sound beyond the limits of conventional wireless technology.
- Automatic Frequency Selection
- Automatic Transmitter Setup
- 960 Selectable frequencies across 24 MHz bandwidth
- Detachable 1/4 wave antennas
- Microprocessor-controlled diversity
- RF presence LED
- 5-segment audio meter
- Multi-function, backlit LCD
- Low battery indicator
- Frequency and power lockout
- Rugged metal chassis
- Volume control on rear of unit
- 1/2 rack design
- Furnished rack hardware
- Non-slip bumpers for use out of rack
- XLR and 1/4" outputs
|
The SR 400 diversity receiver is your best choice for cost-efficient,
high-performance multichannel systems. Up to 12 channels* can be
used simultaneously within the same subband and even large systems
will work smoothly in environments hostile to RF transmission.
Being compatible with professional WMS 4000 antenna splitters,
power supplies, and high quality antennas, the WMS 400 enables
you to set up highly complex wireless systems. In Auto Setup mode,
the receiver will scan the available bands, find an interference-free channel,
and transmit the related frequency data to the assigned transmitter via infrared.
This technique significantly reduces the time it takes to set up a multichannel
system. A Rehearsal function identifying dead spots, a programmable display
clearly indicating all important system parameters, twocolor display backlighting
warning the user of critical conditions from a distance, and a transmitter battery
status display on the receiver enhance reliability and add to ease of use.
Features:
* Integrated frequency scanner with frequency management database
* Up to 12 channels can be used simultaneously in each subband
* Infrared data transmission link
* Rehearsal function for finding dead spots
* Programmable warning functions using two-color display backlighting
Specifications:
* Carrier frequency range: 650 to 680, 680 to 710, 720 to 750,
760 to 790, 790 to 820, 835 to 862 MHz
* Modulation: FM
* Audio bandwidth: 35 to 20,000 Hz
* THD: |
Designed for on-camera mounting, the FP5 Portable Receiver locates an open frequency at the touch of a button and instantly syncs the transmitter to the receiver frequency.
The battery-powered FP5 is lightweight and durable, featuring diversity antennas and output to either XLR or 1/8" connectors.
For use with FP Wireless and SLX Wireless.
FP Wireless Systems feature patented Audio Reference Companding for crystal-clear sound beyond the limits of conventional wireless technology.
Power LED with low battery indicator
RF LED that indicates transmitter sync when illuminated
Receiver output level control that manages output to camera/mixer
Diversity antennas for consistent reception of signal transmission
TA3F cable output to either XLR or 1/8" connectors included
Camera shoe mount included
Rugged and lightweight Shure construction
Audio Output Type
TA3F
Configuration
Impedance balanced
Pin Assignments
1=ground, 2=hot, 3=cold
Maximum Audio Output Level (Ref. ±38 kHz deviation with 1 kHz tone)
–5 dBV (into 600 Ω load)
Impedance
200 Ω
Dimensions
108 mm x 64 mm x 19 mm (H x W x D)
Weight
81 g (3 oz.)
Housing
Molded polycarbonate case
Sensitivity
–108 dBm for 12 dB SINAD, typical
Power Requirements
LR6 AA batteries, 1.5 V
Battery Life
Up to 12 hours (alkaline)
Bandwidth
24 MHz
Compatible Systems
Up to 20, simultaneous
|
The IR-702T is a 2-channel infrared wireless tuner employing a fixed frequency system. This tuner is combined with an infrared wireless microphone and an infrared wireless receiver to make up the infrared wireless microphone system. The infrared microphone system eliminates problems with interference or eavesdropping, allowing simultaneous use in adjacent conference rooms or school classrooms.
(*1) 0 dB = 1 V | Power Source | AC mains, 50/60 Hz (supplied from the included AC adapter) | | Power Consumption | 15 W or less | | Receiving Frequency | Channel A: 3.100 MHz
Channel B: 3.350 MHz | | Receiver Sensitivity | S/N ratio: 50 dB or more
(40 dBμV input, 1 kHz modulation, ±4.8 kHz deviation) | | S/N Ratio | 61 dB or more (60 dBμV input, ±4.8 kHz deviation, A-weighted) | | Tone Squelch Frequency | 32.768 kHz | | Infrared Receiver Input | 75 Ω, BNC jack × 2 (Infrared wireless receiver's power source: 24 V DC,
220 mA max. in total of 2 terminals) | | Output | Channel A and B: -10 dB(*1) (±4.8 kHz deviation, at volume level max.),
600 Ω, electrical balanced, 3 pole phone jack.
Note: Channel A switchable to mixer output. | | Frequency Response | 100 Hz - 12 kHz | | Operating Temperature | -10 ℃ to +50 ℃ (14 ゜F to 122 ゜F) | | Operating Humidity | 30 % to 85 %RH | | Finish | Case: ABS resin, black | | Dimensions | 210 (W) × 44 (H) × 210.9 (D) mm (8.27" × 1.73" × 8.3“) | | Weight | 630 g (1.39 lb) (unit only) | | Accessory | AC adapter(*2) …1, AC Power cord (2 m (6.56 ft))(*2) …1,
Cord with a phone plug (1 m (3.28 ft)) …1, Color label (6 colors) …1,
Rubber foot …4 | | Option | Rack mounting bracket: MB-WT3
MB-WT4 (for mounting with the optional IR-700D
together) |
| Half-rack QLXD4 Digital Wireless Receiver quickly finds open frequencies and deploys them to transmitters via the one-touch sync function.
Works with QLX-D™ Digital Wireless Systems
Features Ethernet networking and mobile monitoring and control capabilities
Includes QLXD4, hardware for rack-mounting, power supply, two 1/2 wave antennas, 2 BNC cables, 2 BNC bulkhead Adapters, and user guide
With transparent 24-bit digital audio quality and incredibly efficient RF spectrum usage, the QLXD4 Digital Wireless Receiver combines professional features with streamlined setup and operation.
Automatic scanning quickly finds open frequencies, and one-touch IR sync quickly deploys them to transmitters.
Ethernet networking enables networked channel scanning across multiple receivers and Wireless Workbench® software integration for remote control of receiver settings from a PC or Mac. Remote monitoring and control from iOS devices also is available via the ShurePlus™ Channels Mobile App.
Features
64 MHz tuning bandwidth (region dependent)
More than 60 preset compatible channels per frequency band (region dependent)
Up to 17 compatible systems per 6 MHz TV channel; 22 systems per 8 MHz channel
Digital predictive switching diversity ensures solid RF connection
AES 256-bit encryption for secure wireless transmission
Up to 60 dB of adjustable audio gain
High-contrast LCD menu and controls with lockout feature
Audio and RF LED meters with peak indicator
Detachable ½ wave antennas
Mic / line switchable XLR output
¼" Instrument output
Durable aluminum construction with brushed finish |
Reviews
There are no reviews yet.