Content |
The ZonePRO 640m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.
The 640m features a total of six inputs and four outputs. Inputs include four balanced mic/line switchable terminal block inputs and two mono-summed pairs of unbalanced RCA inputs. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.
The 640m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth®, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.
A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.
The front panel of the 640m features comprehensive signal metering, an informative LCD display and user-specified front panel control.
Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.
All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).
ZonePRO Designer—the configuration, control and monitoring software for the ZonePRO family of devices—offers control of the ZonePRO 640m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-by-step configuration process of the 640m.
Front Panel LED Indicators
Per Output:4 Independent Six-Segment Lightpipe Output Meters that range from -30 to +20 dBu, Threshold Meters
Other:LCD Display provides information about Source Selection, Page Steering, Zone Volume and Mute
Analog Inputs:
6 Total (4) Switchable Mic or Line, (2) Unbalanced, Mono-Summed RCA Input Pairs
Type:Euroblock (Mic/Line), RCA (Source)
Impedance (Euroblock):>50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):>25kΩ Unbalanced, RF Filtered
Max. Input Line Level:+20dBu Mic/Line, +12dBu RCA
CMRR:> 40dB, typically >55db @ 1kHz
Mic Pre Gain:30 to 60dB
Mic Input Noise (E.I.N.):
Mic Phantom Power:+15VDC
ANALOG OUTPUTS
Number of Outputs: 4 Total
Type:Electronically Balanced, RF Filtered Euroblock
Impedance:120Ω Balanced, 60Ω Unbalanced
Max. Output Level:+20dBu
A/D PERFORMANCE
Type: dbx Type IV™ Conversion System
Dynamic Range line: >113dB, A-weighted, >110dB unweighted
Type IV dynamic range:
>119dB, A-weighted, 22kHz
BW: >117dB, unweighted, 22kHz BW
Sample Rate: 48kHz
D/A PERFORMANCE
Dynamic Range: 112dB A-weighted, 109dB unweighted, 22kHz BW
SYSTEM PERFORMANCE
Dynamic Range: >109dB A-weighted, >106dB unweighted, 22kHz BW
THD+N: 0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response: 20Hz – 20kHz, +/- 0.5dB
Interchannel Crosstalk: >80dB typical
Crosstalk input to
output: >80dB
Propagation Delay 0.6 msec
POWER REQUIREMENTS
Operating Voltage: 100 VAC, 50/60Hz, 120 VAC, 60Hz, 230VAC 50/60Hz
Power Consumption: 29 Watts
BTU: |
Info
The ZonePRO 1260m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus. Features: - 12 Inputs / 6 Outputs - 6 Balanced Mic/Line Inputs - 4 Unbalanced, Mono-Summed RCA Input Pairs - S/PDIF Input - Microphone Gain per Channel - Pre-Configured Architecture - Two Configurable Input Insert Positions - One Configurable Output Insert Position - AutoWarmth per Output Zone - Link Bus - Comprehensive Signal Metering - Front Panel LCD - 9 User-Specified Front Panel Control - Optional ZC Controllers - Ethernet Control - Serial Control - Third Party Control - Wizard-Driven Configuration
|
Intelligent Control Panel, Wall-mountable.
The ICP1 intelligent control panel features controls virtually identical to those on the DME64N/DME24N
front panels, giving operators remote control capabilities for both DMEs. It offers unmatched ease of use
thanks to a large, easy-to-read backlit LCD display that shows names for scenes and function keys in 5
languages – Japanese, English, French, German and Spanish. The 6 function keys appearing at the top
and bottom of the LCD screen can be assigned to most parameters for easy remote control access.
These function keys are defined as a "function key set" or "page“. Up to 4 sets of "pages" are available –
for up to 24 parameters assignable to function keys. Users can change the "page" by pressing the
HOME key. A single function key can be used for simultaneous multiple parameter control by defining
parameter links. Function keys are defined with DME Designer software. |
Audio Network CobraNet CM-1 Module (optional)
CAN Bus Interface 2 x RJ-45
Cooling Left-to-right, 3-stage fan
Data Format 24 Bit linear A/D and D/A conversion, 48 Bit processing
FIR-Drive Yes
GPIO Control Port 2 x 6-pole Euro block4 Control Inputs (analog 0 - 10 V / logic control)3 Control Outputs (Relay contact to ground) 1 Fault Output (NC Relay contact) 3 Reference Outputs (+5 V / +10 V/ GND)
Internal Processing 2 DSPs Standard (150 MHz, 300 MIPS)1 DSP per Audio Module (100 MHz, 100 MIPS)DSP-1 Extension Module optional (+300 MIPS)
Network Control (IRIS-Net) Yes
Network Interface Ethernet-10/100 MBit/s, RJ-45
Power Consumption 90 W max. (incl. 2 x AI-1, 2 x AO-1, 1 x CM-1 modules)
Power Supply 100 - 240 VAC, 50/60 Hz
Sample Rate 48 kHz internal
Serial Interface 2 Ports, 9pin D-Sub female (Remote Control)
Signal-to-Noise Ratio (A-weighted) 115 dB
Total Harmonic Distortion 0.01 %
Height 2RU 88.1 mm (3.47“)
Width 483 mm (19.02“)
Depth 381 mm (15“)
Weight Net 7.37 kg (16.25 lbs)
|
- Connect 2 TVs or projectors and switch between 4 connected HDMI devices.
- HDMI matrix switch allows you to watch other HDMI devices on 2 screens independently.
- Use the built-in 1080p downscaler in case 1 or more screens do not support 4K resolution.
- Suitable for the latest Ultra HD 4K60 resolution (3840 x 2160/60 Hz), High Dynamic Range (HDR), Deep Color and 4:4:4 chroma colours.
- Supports Dolby Atmos and DTS:X and all other common audio formats.
- With additional digital audio output to also connect your AV receiver using a single cable.
- Supports Audio Return Channel (ARC) to avoid lip-sync problems.
- Switches automatically and/or with remote control.
Connections
|
|
AV input |
4 x HDMI |
AV output |
2 x HDMI |
Digital audio output |
1x Toslink (optical) |
Video
|
|
Video resolution |
Max. 4K60 (3840 x 2160@60 Hz) |
PC resolution |
Max. 2560 x 2048 Hz |
Video bandwidth |
18 Gbps |
Clock frequency |
Max. 600 MHz |
HDMI standard |
HDMI, EDID, DVI, Deep Color 36 bit, x.v. Colour and 3D formats |
HDCP standard |
HDCP 2.2 |
Colour formats |
RGB and YCbCr 4:4:4, 4:2:0 or 4:2:2 |
Colour depth |
Max. 36 bit |
Audio
|
|
HDMI audio |
DTS-HD Master Audio, Dolby TrueHD, Dolby Atmos, DTS:X, Dolby Digital/AC3, DTS 5.1 and PCM stereo |
Optical Audio |
Dolby Digital/AC3, DTS 5.1 and PCM stereo |
General
|
|
Dimensions (h x w x d) |
18 x 242 x 104 mm |
Weight |
620grams |
Power |
100-240 VAC 50/60 Hz, 12 VDC adapter |
|
The NAI48-ES is a digital audio network interface that uses the EtherSound network protocol. Digital mixing consoles such as the Yamaha PM5D, M7CL, or LS9 can be connected to AD8HR 8-channel microphone preamp/AD converter or DA824 DA converter units via the NIA48-ES for remote analog input or output interfacing on stage or wherever needed. This type of system eliminates noise problems that are unavoidable with conventional analog console plus multi-cable type setups, and dramatically reduces microphone cable length for superior sound quality. Cabling between the console and "stage box" units is also simplified for fast, easy setup.
48 channels of digital audio each way over a single Cat-5 Ethernet cable EtherSound™ Networking Uncompromising Yamaha Quality, Compatibility, and Reliability
General specifications
Sampling Frequency | 42.9975kHz to 49.2kHz
85.995kHz to 98.4kHz | Maximum I/O channel count | 48 IN/48 OUT (44.1/48kHz), 32 IN/32 OUT (88.2/96kHz) | Power requirements | AC100-240V 50/60Hz, and/or DC12V | Power consumption | 12W | Dimensions (W x H x D) | 480 x 44 x 150mm | Weight | 2.6kg |
Digital I/O characteristics
Terminal | Format | level | Connector |
---|
AES/EBU
1-6 | IN | AES/EBU | RS422 | D-sub 25P | OUT | EtherSound™ | IN | 100Base-TX | 100Base-TX | RJ-45 | OUT |
Control I/O characteristics
Terminal | Level | Connector |
---|
WORD CLOCK | IN | TTL/75Ω | BNC | OUT | HA Remote | RS422 | D-sub 9P |
|
Reviews
There are no reviews yet.