Content |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 800W
4Ω EIA 1 kHz 1% THD - 1250W
2Ω EIA 1 kHz 1% THD - 2000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 2600W
4Ω EIA 1 kHz 1% THD - 4000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.92V
32dB Setting - 1.96V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 36.4dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -105dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 12A
230V 50Hz - 7A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
Live performance DSP amplifier. Fully integrated professional speaker processing with FIR Drive technology . Market leading acoustic performance and rock solid reliability. True 2 ohm stability. Intuitive system control software, makes setup and control easy. Rated power: 2 Χ 2200 Watts/2Ω, 2 Χ 1800 Watts/2,6Ω, 2 Χ 1300 Watts/4Ω, 2 Χ 650 Watts/8Ω.
Manufacturer |
DYNACORD |
Application |
Portable PA |
Channels |
Dual Channel |
Resistance ohms |
8Ω / 4Ω, 2Ω |
DSP |
Yes |
Weight (kg) |
16,2 |
Power (8 ohms/Watt RMS) per channel |
650 |
Power (4 ohms/Watt RMS) per channel |
1300 |
Power (2 ohms/Watt RMS) per channel |
2200 |
Series |
L series |
Model |
L2800FD |
Part Number |
F01U312392 |
Warranty |
3 Years Warranty |
| Amplifier Gain 32 dB
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 2100 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 900 Watts
Continuous Rated Power
(20-20 kHz, THD |
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 1600 Watt rms | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | Power output stereo 8Ω: | 2 x 700 Watt rms | | Power output bridged 4Ω: | 3200 Watt rms | | Power output bridged 8Ω: | 2200 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 102 dB | | Crosstalk: | > 65 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 400:1 (8 W) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 20.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Thermal, temperature, direct current, short circuit, RFI | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 16 A | | Power Consumption: | 6500 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 132 / 5.19 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 455 / 17.91 mm/inch | | Net Weight: | 29.5 / 65.03 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 200 / 7.87 mm/inch | | Package width: | 575 / 22.63 mm/inch | | Package depth: | 555 / 21.85 mm/inch | | Shipping Weight: | 32.5 / 71.64 Kg/Lbs |
|
Amplifier Gain 41.5 dB, 35 dB, 32 dB (switchable)
CAN Bus Interface Optional with RCM-26
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 2000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1450 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 850 Watts
Continuous Rated Power
(20-20 kHz, THD |
Single digital (Class D) amplifier with switching power supply 1200W/70V/100V. Protection against overheating, overcurrent and short circuit output. Features & priority entry program (program override) for message playback emergency. Highpass filter OFF/200Hz/400Hz. Remote control function ON / OFF. Power Supply DC 24V, AC 220 ~ 240V 50/60Hz. |
Reviews
There are no reviews yet.