| 20Hz - 20kHz |
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
| 1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
| 2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
| 4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
| 8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
| Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
| Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
| P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
| 2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
| 4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
DPS 3000 is a 2 channel power amplifier that can handle exceptionally high power ratings in a compact and lightweight 2 rack units space.
Thanks to the class HD technology, this amplifier delivers up to 2 x 1700 W RMS @ 2 Ohm (3400 W RMS bridged @ 4 Ohm), weighting just 14 kg.
It comes with a ʽPFCʼ (ʽPower factor correctionʼ) switched mode power supply which ensures that a predominantly
resistive load is presented to the mains power supply; this also leads to an improved amplifier performance at high output levels. Thanks to its high efficiency heat sinks and variable speed DC fans, the DPS 3000 can withstand the hardest heat conditions ensuring great reliability.
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 2Ω: | 2 x 1700 Watt rms | | | Power output stereo 4Ω: | 2 x 1200 Watt rms | | | Power output stereo 8Ω: | 2 x 800 Watt rms | | | Power output bridged 4Ω: | 3400 Watt rms | | | Power output bridged 8Ω: | 2400 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | 108 dB | | | Damping factor: | > 1000 | | | Slew rate: | 55 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | xlr | | | Input sensitivity: | 1.4 dBm/V RMS | |
| OUTPUT SECTION |
|---|
| Output connector: | Speakon | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Temperature-controlled fan | | | Protections: | Temp., DC, RFI, short-circuit | | | Voltage gain: | 32 – 26 dB | | | Amplifier class: | HD | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 90 ÷ 245 V (50 / 60 Hz) V ~ Hz | | | Power Consumption: | SMPS W | | | Power factor (cos φ): | 0.95 from 200 W to full power | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88/3.4 mm/inch | | | Width: | 482/18,9 mm/inch | | | Depth: | 420/16.5 mm/inch | | | Net Weight: | 14/30.8 Kg/Lbs |
|
The new flagship of the LX series delivers a mighty 2 x 2100 watts into 2 ohms and 2 x 1500 watts into 4 ohms and therefore has plenty of headroom for large subwoofer arrays. For decades, DYNACORD has been one of the leading manufacturers in the pro audio sector and has established a secure position in the amplifier market thanks to the excellent audio performance,absolute reliability and high stability of the Linear Precision series. With their outstanding operational security, which guarantees years of problem-free use, the amplifiers of the Linear Precision series are now the standard for a wide variety of full-range and multi-way loudspeakers systems in professional venues as diverse as theatres, stadiums, discotheques, clubs and concert halls. Datasheets / ManualsManual (2.2MB)
Load Impedance 2 O, 4 O, 8 O Max. Midband Output Power, THD = 1%, 1kHz 2 O - 2100 W, 4 O - 1500 W, 8 O - 900 W Rated Output Power, THD 300 Slew Rate 38 V/µs Signal to Noise Ratio, A-weighted 108 dB Output Stage Topology Class H Power Requirements 100V, 120V, 220V, 230V, 240 V; 50Hz … 60Hz (factory configured) Power Consumption, 1/8 max. output power @ 4 ohms 1070 W Protection Audio Limiters, High Temperature, DC, HF, Back-EMF, Peak current Limiters Inrush Current Limiters, Turn-On delay Cooling Front-to rear, 3-stage fans Ambient Temperature Limits +5° … +40° ( 40°F … 105°F ) Safety Class I Dimensions ( W x H x D ) mm 483 x 88.1 x 384 Weight 8.70 kg (19.2 lbs) Optional Accessories Rear Rackmount 15.5" D112 930 (RMS15-CL), Rear Rackmount 18.0" D112 933 (RMS18-CL), LPN + Lo-Cut Filter D112963 (NRS 90268)
| Amplifier Gain 32 dB
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 2100 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 900 Watts
Continuous Rated Power
(20-20 kHz, THD | Electro-Voiceʼs new Precision Series Compact amplifiers offer proven Precision Series performance and reliability in a new compact, lightweight format made possible by a highly efficient Class-H design, which generates considerably less heat. The CP3000S is not only the first Precision Series amplifier to use a switch-mode power supply, but also the first switch-mode amplifier with EVʼs Precision Series sound. With up to 2x1600 watts into two ohms, and 2x1100 watts into four ohms, and only 17.96 lbs (8.15 kg it is both powerful and lightweight.
1U Panel w/ 8 XLRM + 8XLRF 2Amplifier Gain 32 dB
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 1600 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1100 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 600 Watts
Continuous Rated Power
(20-20 kHz, THD |
Reviews
There are no reviews yet.