Content |
The C4 is small diaphragm condenser microphone featuring interchangeable capsules, switchable -10dB pad/high pass filter and a linear low-noise, solid state amplifier body. The microphone?s modularity makes it a useful multi-purpose tool intended for all-around use on stage, on location and in studios of all caliber. As a cardioid (pressure gradient) microphone, the C4 provides excellent pickup of on-axis sources while attenuating extraneous sound occurring from around and behind the mic. This makes it ideal for close miking of individual instruments where bleed from other nearby instruments or sound is undesirable. The C4 cardioids also make excellent stereo pairs for coincident and near-coincident miking techniques such as X-Y and ORTF. Additionally the C4?s are quite useful on a drum kit as overheads and on toms. Used as an omni-directional (pressure) microphone, the C4 offers a warm tonal response and is recommended especially for close miking in favorable acoustical environments. There is very little off axis coloration owing to the inherent physical properties of pressure capsules, and it is this - combined with the low self-noise of the microphone amplifier that makes the C4 omni an excellent ambience mic ?especially in pairs. In a good room, a pair of omni?s can provide a vibrant and live feel to recordings, which is not achievable through the use of directional microphones. Recommended uses are, spaced pair omni, Jecklin disc (OSS), piano, guitar, drum overheads and room miking. The C4 is available in pairs with shockmounts, windscreens and case.
Features: Studio Quality Stereo Pair Microphone System Modular Design Interchangeable Capsules (Omni, Cardioid) Switchable -10dB pad/ High Pass Filter Transformerless Output Rugged Construction
Applications: Coincident, Near Coincident Pair Spaced Pair Omnis Location Use Spot Miking For Instruments Ambient Recording Drum Overheads
Included Accessories: Shock Mount Adapter Foam Windscreen Pair of Cardioid Heads Pair of Omni Heads Case
Technical Description Type: Single diaphragm modular FET condenser microphone Polar Pattern: Cardioid (CC1) Omni-directional (OC1) Frequency Response: 40Hz.~20kHz Sensitivity: 12m V/Pa. where 1 pa = 94dB SPL Output Impedance: 1200 Ohm Max SPL: 150 dB SPL with -10dB pad Equivalent Noise: 16 DB SPL, (A-weighted per IEC268-15) S/N Ratio: 78 dB Power Requirement: P48 +/-4V Current Consumption: |
Acoustical operating principle | Pressure transducer | Directional pattern | Omnidirectional | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohm | 20 mV/Pa | Rated impedance | 50 ohms | Rated load impedance | 1000 ohms | Equivalent SPL CCIR 468-3 | 28 dB | Equivalent SPL DIN/IEC 651 | 15 dB-A | S/N ratio CCIR 468-3 | 66 dB | S/N ratio DIN/IEC 651 | 79 dB | Max. SPL (tube characteristic) | K | Dynamic range (of the amplifier) | K | Maximum output voltage | 8 dBu | Weight | 800 g | Diameter | 78 mm | Length | 165 mm |
* THD of the microphone amplifier at an input voltage which is equivalent to the capsule output voltage at the specified SPL.
|
Large diaphragm cardioid microphone | Pressure gradient transducer with with one-diaphragm capsule | Transformerless circuitry | Extremely low noise: 7 dB-A | Includes swivel mount | Straightforward handling for homerecording and professional studios |
High-quality professional equipment for limited budgets
Acoustical operating principle | Pressure gradient transducer | Directional pattern | Cardioid | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohm | 23 mV/Pa | Rated impedance | 50 ohms | Rated load impedance | 1 kohms | Equivalent noise level, CCIR1) | 17.5 dB | Equivalent noise level, A-weighted1) | 7 dB-A | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 76.5 dB | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 87 dB | Maximum SPL for THD 0.5%2) | 138 dB | Maximum output voltage | 13 dBu | Dynamic range of the microphone amplifier (A-weighted) | 131 dB | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | Current consumption (P48, IEC 61938) | 3 mA | Matching connector | XLR3F | Weight | approx. 450 g | Diameter | 60 mm | Length | 132 mm |
|
|
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm | Live sound
Podcasting
Home recording
Vocals
Musical instruments |
Perception 120 |
|
- General-purpose cardioid recording microphone
- Extended frequency response
- Roadworthy construction
- Switchable 20 dB preattenuation pad
- Switchable bass cut filter
- Designed and engineered by AKG in Vienna, Austria
The Perception 120 is a 2/3-inch diaphragm true condenser microphone that offers solid build quality, outstanding performance, and excellent value. The low-mass diaphragm delivers a clear sound with accurate sonic detail. A switchable 20 dB preattenuation pad and bass cut filter make the Perception 120 an excellent choice for a wide range of recording and live sound applications.
Backed by AKG\'s six decades of experience in making microphones and input from sound engineers around the world, the Perception 120 now brings AKG studio quality to musicians and project studio applications.
Type |
2/3\" Diaphragm True Condenser |
Polar pattern |
cardioid |
Frequency range |
20 to 20,000 Hz |
Sensitivity |
22 mV/Pa (-33 dBV) |
Max. SPL |
130/150 dB (0/-20 dB) for 0.5% THD |
Equivalent noise level |
22 dB-A (IEC 60268-4) |
Signal/noise ratio (A-weighted) |
72 dB |
Preattenuation pad |
0 dB, -20 dB |
Bass filter |
12 dB/octave at 300 Hz |
Impedance |
|
Recommended load impedance |
>= 1,000 ohms |
Powering |
|
Power requirement |
48 V phantom power to DIN/IEC |
Connector |
3-pin XLR |
Finish |
metallic blue |
Dimensions |
53 dia. x 165 mm (2.1 dia. x 6.5 in.) |
Net weight |
525 g (18.5 oz.) |
Shipping weight |
955 g (33.7 oz.) |
|
The AVANTONE CK-6 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET mics…but at a fraction of their cost!
The rugged CK-6 microphone body and capsule assembly are precision machined of Brass. Aesthetically the compact body features an elegant Metallic Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly. Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.
This Transformerless CLASS A FET Microphone w/ 32mm gold sputtered thin Mylar capsule is designed with circuitry that will yield pleasing professional results comparable to much more expensive designs. It also features -10 dB pad & 80 Hz LF roll off switches for varied recording situations.
The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.
Applications
Studio vocals, acoustic guitar, mandolin, drum overheads, piano, etc…
Specifications
Type: True Transformerless Condenser
Polar Pattern: Cardioid
Frequency Response: 35-20,000 Hz +/- 3.5dB
Output Impedance: |
Reviews
There are no reviews yet.