| Content |
The Scarlett OctoPre Dynamic from Focusrite is an eight-channel preamp and interface suitable for expanding the input array of any studio, and also, for use on stage. Connections are secured via eight combination inputs, each one giving you jacks that accept 1/4" and XLR cables. Two of the inputs can handle Hi-Z instruments as well, allowing you to plug in guitars and basses. Eight 1/4" line outs are also available via the rear panel. Also provided are eight channels of AD/DA conversion up to 192 kHz. This feature, combined with the unit's back-panel ADAT I/O section, renders the Scarlett OctoPre Dynamic quite suitable for expanding the input and output capability of interfaces such as the Scarlett 18i8, 18i20, or indeed, any interface connectable via ADAT. |
The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.
The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.
The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.
The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.
The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
- LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme. | • Road proof housing
• High quality components
• Professional balanced XLR outputs
• Level control
The ASC-202 converts consumer level stereo RCA signals to balanced XLR professional line level, and back. One side of the unit, has two XLR inputs and stereo RCA outputs. The other side has stereo RCA inputs and two XLR outputs. Each side has stereo level controls. A possible application of the SC-13 is to use it as a level control in balanced audio lines.
The DAP Pro Audio Solutions are a complete line-up of audio tools for the professional musician or audio engineer. It is a series of audio modifying tools like mini-mixers, pre-amps and converters available in active or passive models. All audio solutions are designed to meet the highest stage and audio demands and feature a metal road proof housing with rubber feet and easy accessible controls. The units also have a small footprint which make them ideal to be used and placed in any environment where space is critical.
Specifications Frequency Response: 20Hz-20KHz
Inputs: XLR/Jack Combo, RCA
Outputs: XLR male, RCA
Input sensitivity RCA in: -10 dBv
Input Impedance RCA in: 10 kOhm
Input sensitivity XLR/Jack in: +4 dBu
Input Impedance XLR/Jack in: 20 kOhm
Output voltage RCA Out: -10 dBV
Output Impedance XLR Out: 100 Ohm
Output voltage XLR Out: +4 dBu
Output Impedance XLR Out: 200 Ohm
Power supply: 18V AC (adapter included)
Dimensions: 53 x 158 x 135 mm (HxWxD)
Weight: 0,65 Kg | Vacuum Tube Mic Preamp. 12AX7 Vacuum Tube. +48V Phantom Power, 20dB Pad.
This premium tube mic/line preamp features an integrated limiter for studio,
live and hard disk recording applications. It features a carefully-selected
12AX7 vacuum tube with Behringer's UTC technology for exceptional warmth
and lowest noise. Using the MIC100 is a great way to eliminate the "dull"
sound of standard digital recorders & sound cards. Also, it perfectly
complements studio-grade condenser mics. When used as a high-end DI-box,
it ensures outstanding signal integrity. Features also include a phase reverse
switch, +48 V phantom power, a 20 dB pad, and balanced I/O.
The heart of the Tube Untragain is an extremely low-noise microphone preamp
circuitry that uses discrete components and produces a highly trans-parent
sound. In combination with Behringer's tube technology, the operational amplifiers
4580 and a sophisticated circuit topology, the Tube Untragain yields excellent
noise and distortion properties. The innovative UTC circuitry that has been developed
by our engineering team offers an abundance of sound-shaping possibilities.
Absolute musicality was Behringer's major goal when we designed the Tube
Untragain. The result is a device that, thanks to our tube circuitry, lends an
incredible punch to percussion instruments. On the other hand, instruments
that are rich in upper harmonics will receive more transparency. The sound
will be warm, detailed and brilliant.
Technical Description
Specifications
XLR input Connector: Balanced/unbalanced
Type: Transformerless, DC-decoupled input
Impedance: Approx. 2 kOhms
Maximum input level: +7 dBu / 20 dB with pad
1/4 in. TRS input Connector: Balanced/unbalanced
Type: Transformerless, DC-decoupled input
Impedance: Approx. 1 MOhms
Maximum input level: +16 dBu / 20 dB with pad
Audio outputs Connectors: XLR and 1/4 in. TRS connector balanced/unbalanced
Type: Transformerless, DC-decoupled output
Impedance:
Approx. 700 Ohms balanced
Approx. 350 Ohms unbalanced
Maximum output level: Approx. +26 dBu @ 100 k§?
System Frequency Response Mic input: |
The OctaMic II provides 8-Channel 192 kHz / 24 bit AD conversion with eight hi-class microphone and line pre-amplification channels, featuring a combination of sophisticated components and approved RME technology.
Lowest distortion, excellent signal to noise ratio and perfectly linear frequency response transmit and amplify the microphone signals truly unchanged.
The OctaMic II includes some significant enhancements compared to the OctaMic:
The balanced TRS inputs of the Neutrik Combo XLR jacks are phantom power-free and can be operated as real line inputs too. The improved design of the input circuits allows for a maximum input level of +21 dBu with a convenient gain range from 6 dB up to 60 dB.
Improved signal to noise ratio (SNR) ADC 107.5 dB
Improved THD, especially at higher gains
Optimised heat dissipation by a new and larger housing with improved convection
Internal wide range power supply with line filter, insensitive to voltage fluctuations
Super-stable, short circuit proof 48 V phantom power
Features
OctaMic II offers 8 balanced XLR mic / line inputs via Neutrik XLR/TRS combo jacks. Each channel contains switches for 48V phantom power, a low cut filter and phase reversal. Amplification can be set between 6 and 60 dB. LEDs for signal, clip, and activated phantom power give a complete overview on the unit's status. When the special Clip Hold mode is activated, any detected clip-state will cause the corresponding LED to flash once per second. With this, the user gets a long-term peak detection, and no longer needs to constantly watch the LEDs. At the same time momentary overloads are still displayed correctly.
Frontside switches include power on/off and output level, for a choice of -10 dBV, +4 dBu or Hi Gain (+19 dBu) as reference level. This unusual feature offers two advantages. First, the reference level can be easily switched to match any of RME's current interface devices, from HDSP 9632 through Multiface up to the renowned ADI-8 series converters. Second, the Signal to Noise ratio is optimized, and the Clip-LED will exactly match the ones of the ADI-8 (2 dB below 0 dBFS).
The balanced line level output signal is available at the back of the unit via 8 stereo TRS jacks. The specially developed, internal hi-performance switch mode power supply lets the OctaMic II operate in the range of 100V to 240V AC. It is short-circuit-proof, has an integrated line-filter, is fully regulated against voltage fluctuations, and suppresses mains interference.
Top
AD-Conversion
The 8-Channel AD-conversion of the OctaMic II operates at up to 192 kHz. The digitized signal is available simultaneously at the double ADAT output (S/MUX, up to 96 kHz), and at a DB-25 connector (4 AES/EBU outputs, up to 192 kHz). The digital part can be clocked internally (master) and externally via word clock, AES/EBU and SPDIF.
RME's outstanding SteadyClock(TM) ensures perfect AD-conversion, as jitter on the external sync-sources is nearly completely removed. All settings are done via DIP-switches on the back of the OctaMic II. Analog outputs and both digital outputs operate fully simultaneously. The choice of reference level affects the analog outputs only, the signal/clip indication and the AD-conversion will react only to the Gain-pots.
Top
Tech Specs
8 balanced XLR/TRS mic/line inputs
54 dB gain range
Input impedance: XLR 2 kOhm, TRS 5 kOhm
Analog input level: from -40 dBu up to +21 dBu
Maximum output level: +21 dBu
Output impedance: 75 Ohm
Output level switchable Hi Gain / +4 dBu / -10 dBV
Signal to noise ratio (SNR): 129 dB EIN @ 150 Ohm
THD:
Large frequency range (200 kHz) with special EMI input filtering
Frequency response -0.5 dB: 5 Hz - 200 kHz
Hi-pass filter: 80 Hz, 18 dB/oct.
Line Out: 1/4" TRS (6.3 mm stereo jack), servo-balanced
Phantom power: +48 Volt switchable per channel
Internal wide range switching power supply 100-240 Volt AC
Unbeatable price/performance ratio!
AD conversion
SNR: >110 dB(A)
Supported sample rates: 28 kHz - 200 kHz
THD:
Sync Sources: AES/EBU (also SPDIF coaxial), wordclock, internal
SteadyClock(TM) ensures best sound quality even with jittery external clocks
Top
Accessories
Digital breakout cable Pro, AES/EBU, D-sub25 to 4x XLR-3 female + 4x XLR-3 male, 1m/3m/6m (ALVA Audio)
Digital D-sub cable, AES/EBU, D-sub25 male to D-Sub25 male, 1m/3m/6m (ALVA Audio)
Optical ADAT Toslink cable 1m/2m/3m/5m/10m (ALVA Audio)
Word Clock cable, 1 x BNC male to 1 x BNC male, 1m/5m/10m (ALVA Audio)
Top
Add-On
BOB-32 Universal Breakout Box with 2 x 8 XLR to 2 D-sub connectors (supports TASCAM and YAMAHA format), flip-frame case
|
- 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
- Gain control, 10 steps (6-50 dB)
- Phantom power can be switched on
- Clip LED
- 1 line output, XLR (bal.) or 6.3 mm (unbal.)
- Operation via supplied power unit
| Power supply: | 12 V DC, 150 mA | | Input impedance: | 10 kohms bal./unbal. | | Max. input level: | +4 dB bal./+10 dB unbal. | | Gain: | 50 dB XLR/44 dB jack | | T.H.D.: | 0.01 % | | Frequency range: | 25 Hz - 16 kHz | | S/N ratio: | >75 dB | | Dimensions: | 143 x 93 x 45 mm | | Weight: | 350 g |
|
Reviews
There are no reviews yet.